!!!!!Application reference missing: ACAD, to AcDbMaterial!!!!!

[Anonymous]

"Application reference missing: ACAD, to AcDbMaterial
Object reference missing: AcDbXrecord, to AcDbDictionary."

now i can't refedit the xrefs i work with please help me.

This is a serious problem!!!!!!! please reply if you are sure for 100% how to handle with this problem.

[Anonymous]

This has nothing to do with DBlock, as far as I can determine. Don't
cross-post.

--
R. Robert Bell


wrote in message news:5524608@discussion.autodesk.com...
"Application reference missing: ACAD, to AcDbMaterial
Object reference missing: AcDbXrecord, to AcDbDictionary."

now i can't refedit the xrefs i work with please help me.

This is a serious problem!!!!!!! please reply if you are sure for 100% how
to handle with this problem.

[Anonymous]

I almost certain it is caused by those external dblocks!!!

[Anonymous]

Have you run Audit on your drawings that are affected by this. Run it and make sure it is fixing errors as it goes.

[Anonymous]

You only mention xrefs, not dblocks.

--
R. Robert Bell


wrote in message news:5524674@discussion.autodesk.com...
I almost certain it is caused by those external dblocks!!!

[Anonymous]

Hello tlindell,

Yes but that didn't work. any other suggestions.
I already made wblock of the original drawing.
even that didn't work.

Please help me!!!

[Anonymous]

Post that drawing here, I'll try to do something...


wrote in message news:5524608@discussion.autodesk.com...
"Application reference missing: ACAD, to AcDbMaterial
Object reference missing: AcDbXrecord, to AcDbDictionary."

now i can't refedit the xrefs i work with please help me.

This is a serious problem!!!!!!! please reply if you are sure for 100% how
to handle with this problem.

[Anonymous]

I use autocad 2000/2000i and i can't refedit the drawing
after i attached it in a new drawing.

autocad 2007 no problems!

I appreciate your interest!

[Anonymous]

Well, that's a problem. 2007 significantly changed how materials were
handled. So you are saying that a SaveAs of a 2007-base drawing down to 2000
causes 2000/2000i to complain?

Sorry I cannot help further, since I dumped 2000 about 5 years ago.

--
R. Robert Bell


wrote in message news:5529310@discussion.autodesk.com...
I use autocad 2000/2000i and i can't refedit the drawing
after i attached it in a new drawing.

autocad 2007 no problems!

I appreciate your interest!

[Anonymous]

Here is your cleaned drawing...


wrote in message news:5529310@discussion.autodesk.com...
I use autocad 2000/2000i and i can't refedit the drawing
after i attached it in a new drawing.

autocad 2007 no problems!

I appreciate your interest!

[Anonymous]

thanks. I'll give it a try

Now i'm very curious, how, what did you do with it?

[Anonymous]

What was the solution to this??

[gilab]

Hello Quiz,

I see you have ignored the earlier requests for the specific solution for this problem. We just ran into the same problem and I would very much appreciate it if you would share the fix with me and the rest of the community!

[Anonymous]

Hello there,

i did not get the answer from qiuz ether!!!

[Anonymous]

Copy all geometry to a new drawing in your older version. Copy all of the layouts, use design centre if you have it.

Problem goes away. It's a nuisance, but that's the only fix that I'm aware of.

[Anonymous]

Hello,
I have encountered also the same problem? With error message:

Application reference missing: ACAD, to AcDbLinetypeTableRecord.

I tried both the audit and the copy to new drawing but those didn't work!?@#... I also tried to rename the block and purge, still not successful... anyone has any other brilliant idea on this? PLEASE HELP...

[Anonymous]

The drawing contains Macros. I wblocked them out to a new drawing, then they seemed to disappear.


Try this.. not sure if it will help, or not. Message was edited by: sschwartz

[Anonymous]

try my solution....

get suspect culprit

wblock 

save to dxf /

import dxf back to main dwg

IT SOLVES IN MINE

I CAN REFEDIT,

NOTE BUT NOT TESTED TO XREFEDIT

i assume it would be ok

happy acad dears .!   :D:D:D

[filizcabuk]

I found a 3D line in the block I made and when I fixed it, the problem was solved.