Workstation configuration to run a model above 200000 nodes

[Anonymous]

Dear all,

Currently i am trying to analyze a heavy Robot model with about 200000 nodes ( It is a 70 storey building).

My laptop takes about 5 hours to run the model. Also after analyzing it is hard to rotate and filter results quickly because it is too heavy. ( Analyzed model is about 15 Gb)

I am planning to assemble a workstation to run this model quickly and filter results with following configuration

Processor     -  Intel Core i7 7700k 4.2-4.5 Ghz Quad Core (7th Generation)

RAM            -  Team elite plus 16 Gb 2400 MHz DDR4

Graphiocs    -  Palit Geforce GTX 1050 StormX 2Gb GDDR5

SSD              - Toshiba Q300 240Gb SATA 6Gbps SSD

Hard drive    - Seagate Barracuda 1 Tb 7200RPM

I would like to know whether this configuration would help me to run and analyze this model quickly and easily.

If not please give me a suitable configuration to run my model

Thank You!

[Rafal.Gaweda]

32+ GB RAM 

If you are able to reduce number of panels....

Send us model to check

[Anonymous]

Thank you  Rafal.

sorry i cant send you the model at the moment.

Are you suggesting that my proposed hardware configuration will do my job with a 32 Gb RAM ?

Which hardware should i improve to make the model easy to rotate and filter after analyzing ?

Regards,

Sandeepa

[Rafal.Gaweda]

Are you suggesting that my proposed hardware configuration will do my job with a 32 Gb RAM ?

I hope.

Which hardware should i improve to make the model easy to rotate and filter after analyzing ?

 Reduce number of panels in model if possible.

[Anonymous]

Since it is a already modeled one by the designer the number of panels cannot be reduced.

Is there any way to send you this model to check privately. Since it is confidential.

[Rafal.Gaweda]

https://forums.autodesk.com/t5/robot-structural-analysis-forum/sending-bigger-files/td-p/3795062

+ Private Message on Forum

[Anonymous]

Check private masseges

I have send you the model

Thank You!

[Rafal.Gaweda]

Log from calculations (Robot 2017 SP2):

I will check on 2015 SP5 later. In the meantime please install SP5 for your Robot.

08:03:06 - Structure preparation for analysis #0
08:15:12 - End of preparation for analysis #0
08:15:12 - Start of analysis #0
08:22:20 - Instability (of type 3) detected at node 30284 in direction RZ. #0
Do you want to continue?
[Press ESC to ignore all warnings] #0
08:50:14 - End of analysis #0

My laptop

(Robot uses max 6 GB RAM during calculations as far as I have seen ; so 16 can be enough depending on other opened applications)

[Anonymous]

How is the ability to rotate and filter results in you machine after running the model?

[Rafal.Gaweda]

Check 2017 version:

http://www.autodesk.com/products/robot-structural-analysis/free-trial

then install SP2, then check your model on this version

[Rafal.Gaweda]

2015 :

09:57:53 - Structure preparation for analysis #0
10:12:51 - The element is not assigned to any story #0
10:12:51 - End of preparation for analysis #0
10:12:51 - Start of analysis #0
10:33:54 - Number of missing eigenvalues found = 1. #0
10:53:52 - End of analysis #0

More less the same time

[Anonymous]

ok i will install it

But my other concern is rotating the model after analyzing. currently its very hard to rotate and select elements on my machine

[Anonymous]

Thank you very much !

[Anonymous]

One other thing.. what is your Graphic Card?

[Rafal.Gaweda]

NVIDIA K2100M , 2 GB RAM.

[Anonymous]

Can you please show me the way to get 

1) Bending moments in core wall.

2) Forces of the connection of the two towers at level 39 to 42.

3) How to perform dynamic analysis

4) I am confused with load cases generated and i want to know how to get maximum force diagrams

I have sent you the model before

Thank you!