Community
Civil 3D Forum
Welcome to Autodesk’s Civil 3D Forums. Share your knowledge, ask questions, and explore popular AutoCAD Civil 3D topics.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

I have problem with cross sections.

3 REPLIES 3
Back to Civil 3D Category
Back to Topic Listing
Reply
Message 1 of 4
Anonymous
330 Views, 3 Replies
‎10-14-2003 05:59 AM

I have problem with cross sections.

Anonymous
Not applicable
‎10-14-2003 05:59 AM
Please let me know if I'm in the wrong group.
In my Design Control I set my slopes cut/fill to 3:1. I run it and I get this Warning only on the right side only "right side pinned to end". I am looking for what I'm doing wrong because if you check the design information it's correct but the actual is wrong. My surface and the left side is correct. What is the reason the "pinned to end" warning come up? Any help would be great.
Thanks
Douglas
0 Likes
‎10-14-2003 05:59 AM

I have problem with cross sections.

Please let me know if I'm in the wrong group.
In my Design Control I set my slopes cut/fill to 3:1. I run it and I get this Warning only on the right side only "right side pinned to end". I am looking for what I'm doing wrong because if you check the design information it's correct but the actual is wrong. My surface and the left side is correct. What is the reason the "pinned to end" warning come up? Any help would be great.
Thanks
Douglas
Report
0 Likes
Reply
3 REPLIES 3
Message 2 of 4
Anonymous
in reply to: Anonymous
‎10-14-2003 06:58 AM

Anonymous
Not applicable
‎10-14-2003 06:58 AM
Hi Douglas,

You simply haven't sampled wide enough and the message says it has pinned
the actual to the edge of your sampled section.

--


Laurie Comerford
CADApps
www.cadapps.com.au

"Carreau" wrote in message
news:f192ff8.-1@WebX.maYIadrTaRb...
> Please let me know if I'm in the wrong group.
> In my Design Control I set my slopes cut/fill to 3:1. I run it and I get
this Warning only on the right side only "right side pinned to end". I am
looking for what I'm doing wrong because if you check the design information
it's correct but the actual is wrong. My surface and the left side is
correct. What is the reason the "pinned to end" warning come up? Any help
would be great.
> Thanks
> Douglas
0 Likes
‎10-14-2003 06:58 AM

Hi Douglas,

You simply haven't sampled wide enough and the message says it has pinned
the actual to the edge of your sampled section.

--


Laurie Comerford
CADApps
www.cadapps.com.au

"Carreau" wrote in message
news:f192ff8.-1@WebX.maYIadrTaRb...
> Please let me know if I'm in the wrong group.
> In my Design Control I set my slopes cut/fill to 3:1. I run it and I get
this Warning only on the right side only "right side pinned to end". I am
looking for what I'm doing wrong because if you check the design information
it's correct but the actual is wrong. My surface and the left side is
correct. What is the reason the "pinned to end" warning come up? Any help
would be great.
> Thanks
> Douglas
Report
0 Likes
Reply
Message 3 of 4
Anonymous
in reply to: Anonymous
‎10-14-2003 07:04 AM

Anonymous
Not applicable
‎10-14-2003 07:04 AM
Hi,

Yes you are. I'd replied before I noticed.

Go to the land desktop group.

--


Laurie Comerford
CADApps
www.cadapps.com.au

"Carreau" wrote in message
news:f192ff8.-1@WebX.maYIadrTaRb...
> Please let me know if I'm in the wrong group.
> In my Design Control I set my slopes cut/fill to 3:1. I run it and I get
this Warning only on the right side only "right side pinned to end". I am
looking for what I'm doing wrong because if you check the design information
it's correct but the actual is wrong. My surface and the left side is
correct. What is the reason the "pinned to end" warning come up? Any help
would be great.
> Thanks
> Douglas
0 Likes
‎10-14-2003 07:04 AM

Hi,

Yes you are. I'd replied before I noticed.

Go to the land desktop group.

--


Laurie Comerford
CADApps
www.cadapps.com.au

"Carreau" wrote in message
news:f192ff8.-1@WebX.maYIadrTaRb...
> Please let me know if I'm in the wrong group.
> In my Design Control I set my slopes cut/fill to 3:1. I run it and I get
this Warning only on the right side only "right side pinned to end". I am
looking for what I'm doing wrong because if you check the design information
it's correct but the actual is wrong. My surface and the left side is
correct. What is the reason the "pinned to end" warning come up? Any help
would be great.
> Thanks
> Douglas
Report
0 Likes
Reply
Message 4 of 4
Anonymous
in reply to: Anonymous
‎10-14-2003 07:32 AM

Anonymous
Not applicable
‎10-14-2003 07:32 AM
Why wide should you sample.
My first try I sampled 40m wide
My second Try I sample 100m wide.
I got the same results right side was not following the design.
0 Likes
‎10-14-2003 07:32 AM

Why wide should you sample.
My first try I sampled 40m wide
My second Try I sample 100m wide.
I got the same results right side was not following the design.
Report
0 Likes
Reply
Reply

Forums Links

Can't find what you're looking for? Ask the community or share your knowledge.

Post to forums  

Rail Community


Autodesk Design & Make Report

Report a website issue