Community
If you are using text mask on your mtext and the mask is too wide (see image-1), you can make the mask width the appropriate size.
Select the all the mtext or a large amount of mtext. Then with the mtext selected go to Properties Palette and change 'Paper defined Width' from *VARIES* to 0 (zero). See image-2. After you've made it 0, the mask will 'shrink' to fit the width of your mtext.
Chicagolooper
When mtext is created, if your mtext editor settings are set to display the ruler, the user can click on the diamond at the end of the ruler and drag it left or right to adjust the width of the mtext box.
If the user double clicks on the diamond, the width of the mtext box is reduced to the smallest width required to contain the text. In other words, "the exact width of the text".
In my original post, I suggested a scenario where the scale of a plan drawing was reduced by half with many instances of mtext with background masks. When reducing the height of all the mtext to match the scale, the width of the mtext box becomes twice as long as necessary which isn't normally an issue but in this case it is because of the background masks. Yes, grabbing all instances of mtext and adjusting its width to 0 is a viable solution. For some unknown reason, there are times when the Defined Width property is grayed out and the user isn't able to adjust it to 0. Does that help pendean?
I am looking for a lisp routine that adjusts the width of multiple mtext objects to match the exact width of the text string rather than manually edit each individual instance of mtext by double clicking on the diamond on the ruler.
Thank you all for posting replies.
To optimize the size of your text mask so the mask doesn’t have ‘extra space’, you’ll need to properly define the area where you want to place your text. This involves clicking-and-dragging a text box at the beginning of the mtext command. For middle center justified mtext, drag out a box that’s too wide and you’ll have extra space on both sides or drag a box too tall and you’ll have too much space above and below.
We don’t want to waste valuable time calculating the ideal box size, we have better things to do like watch Youtube and scratch itches in nsfw bodily places that some countries consider jailable offenses..
To make text mask 'hug' your mtext, there are two things you can do. Unfortunately, neither of them is good for existing mtext, e.g. when you change the drawing scale and the annotative text size gets smaller—they’re more suitable for new individual mtext, especially during the initial mtext creation. If you have a lot of existing mtext, then you can't use either of these options and will have to resort to the method described in post #2 of this thread.
- For middle center justified text, you’ll get five grips i.e., one in the middle plus four more in each corner, where the corners literally 'defines the extents' of your text box. To reduce the width so the box ‘hugs’ your mtext, double click on the arrows shown below. The box will reduce and so will your mask.
1-Mtext with middle center justification.
- While in the mtext command, select the ‘Width’ option after your first click and before the second click. When prompted for width, enter 0. After 0, you may finish your second click. (These two clicks, e.g. upper left and lower right, will define your text box area.) For middle center justified text, the 0 width will force your mask to hug your mtext even though you won’t have the customary four corner grips.
2-Select 'W" for width during the mtext command. Enter Width=0.
The image below illustrates mtext using the two options above for middle centered justification. When width=0, you have a center grip. The mask will hug your mtext. If you have a second and third line, it’ll hug the widest of your three mtext lines.
For existing annotative mtext that are subjected to size reductions due to drawing scale changes, you'll have to select all existing mtext, and by all I mean you DO NOT HAVE TO ADJUST EACH PIECE OF TEXT INDIVIDUALLY, you are doing it in a single operation, then force the width to 0 for all those entities in the Properties Palette.
Chicagolooper
Forums Links
Can't find what you're looking for? Ask the community or share your knowledge.
Post to forums
