Announcements
Attention for Customers without Multi-Factor Authentication or Single Sign-On - OTP Verification rolls out April 2025. Read all about it here.

Aussenkontur rundung bearbeiten bei holz mit schlichtfräser

Anonymous

Aussenkontur rundung bearbeiten bei holz mit schlichtfräser

Anonymous
Not applicable

Hallo zusammen

 

Ich habe ein Bauteil das bearbeiten muss.

Hab das meiste auch hingekriegt, nur berechnet mir fusion 360 meine Aussenkontur nicht bis ganz zum Ende.

Das ist ärgerlich da ich so sehr viel schleifen muss.

 

Ich möchte das der Fräser bis auf die Fläche fährt nach oben. (siehe Bild)

 

Weis jemand wie ich das programmieren muss?

Herzlichen Dank für eure Hilfe.

Aussenkontur.png

 

0 Likes
Reply
Accepted solutions (1)
455 Views
9 Replies
Replies (9)

HughesTooling
Consultant
Consultant

Google translate didn't do a good job on your text but try the settings below.

Tool outside boundary.

Clipboard02.png

Mark

Mark Hughes
Owner, Hughes Tooling
Did you find this post helpful? Feel free to Like this post.
Did your question get successfully answered? Then click on the ACCEPT SOLUTION button.

EESignature


0 Likes

Anonymous
Not applicable

Hi Mark Hughes

 

thanks for our answer.

 

i try in english.

 

this setting i have. 

i have also tested whit "Machining boundary" silhouette, choice and virtuell frame.

and is it always the same problem.

 

you have a other idear?

 

thanks

 

aussenkontur einstellungen 3.pngaussenkontur einstellungen 2.pngaussenkontur komplett.pngaussenkontur einstellungen.png

0 Likes

HughesTooling
Consultant
Consultant

Are you able to share your f3d design? A couple of thoughts looking at your settings. Rest machining might not be a good idea for a finishing op or you need more clearance, Silhouette + 1mm or more.

Mark Hughes
Owner, Hughes Tooling
Did you find this post helpful? Feel free to Like this post.
Did your question get successfully answered? Then click on the ACCEPT SOLUTION button.

EESignature


0 Likes

Anonymous
Not applicable

how i share it?

 


@HughesTooling  schrieb:

Are you able to share your f3d design?

 

0 Likes

HughesTooling
Consultant
Consultant

One the file menu there's an option to Export, just save as an f3d and attach to this thread.

 

Mark

Mark Hughes
Owner, Hughes Tooling
Did you find this post helpful? Feel free to Like this post.
Did your question get successfully answered? Then click on the ACCEPT SOLUTION button.

EESignature


0 Likes

Anonymous
Not applicable

ok

is this ok?

0 Likes

HughesTooling
Consultant
Consultant
Accepted solution

Your biggest problem was Contact Point  Bounds selected instead of Contact Only. I added another surface to stop the tool path machining in the pocket. As it's only selected in this op under Model it is not seen by the other ops.Clipboard02.png

Mark Hughes
Owner, Hughes Tooling
Did you find this post helpful? Feel free to Like this post.
Did your question get successfully answered? Then click on the ACCEPT SOLUTION button.

EESignature


0 Likes

Anonymous
Not applicable

ok thanks

 

i dont say, the model are in a hole in my ground of the cnc.

i dont mill on the ground but now i think its good.

 

 

thank you very much for the help.

i test it now and when is ok, i close this question.

 

i hop my englisch is not sooooo bad :winking_face:

 

 

0 Likes

Anonymous
Not applicable

now i have mill it and it is very very well.

 

thank you so much.

 

next week i try the other part.

 

have a nice week

0 Likes