Post processor for st10/y

[darron.lanier]

Does anyone have a problem with their postprocessor not posting correctly.   I am trying to post a counter bore with millturn and it only post in x and c .   I invited my friend to the part and his posted it correctly. We both down loaded the post from the web site in fusion.   My post is the top post       His is the bottom post.   Any help on this will be greatly helpful.

O01001 (STEVE)
G98 G18
G20
G50 S6000
G53 G0 Y0.
G53 X0.
G53 Z0.

(2D Pocket2)
T101
M154
G28 H0.
G98
G97
P3000 M133
G54
M8
G18
M15
G0 C0.
G0 Z0.6
X0.04 Y0.
Z0.2
G1 Z0.1 F99.4639
Z-0.27 F33.1522
X0.0405 C-5.119 F235.
X0.0418 C-9.821
X0.0438 C-13.798
X0.0465 C-16.891
X0.0496 C-19.08
X0.0531 C-20.427
X0.0566 C-21.037
X0.0602 C-21.021
X0.0638 C-20.485
X0.0673 C-19.523
X0.0705 C-18.213
X0.0736 C-16.62
X0.0763 C-14.8
X0.0785 C-12.945
X0.0805 C-10.964
X0.0821 C-8.884
X0.0833 C-6.727
X0.0843 C-4.514
X0.0848 C-2.266
X0.085 C0.
C120.
C180.
X0.0852 C186.302
X0.0859 C192.56
X0.0869 C198.729
X0.0884 C204.773
X0.0903 C210.661
X0.0924 C216.371
X0.0949 C221.889
X0.0977 C227.207
X0.1008 C232.322
X0.104 C237.238
X0.1074 C241.963
X0.111 C246.503
X0.1147 C250.872
X0.1185 C255.079
X0.1223 C259.136
X0.1263 C263.056
X0.1302 C266.848
X0.1342 C270.524
X0.1381 C274.093
X0.1421 C277.564
X0.146 C280.947
X0.1499 C284.248
X0.1537 C287.476
X0.1574 C290.635
X0.1611 C293.733
X0.1647 C296.774
X0.1682 C299.764
X0.1716 C302.706
X0.1749 C305.606
X0.178 C308.467
X0.1811 C311.292
X0.184 C314.084
X0.1868 C316.847
X0.1893 C319.502
X0.1918 C322.134
X0.1941 C324.745
X0.1962 C327.337
X0.1982 C329.912
X0.2001 C332.471
X0.2018 C335.016
X0.2033 C337.548
X0.2047 C340.07
X0.2059 C342.581
X0.207 C345.085
X0.2079 C347.581
X0.2087 C350.072
X0.2093 C352.558
X0.2097 C355.041
X0.2099 C357.521
X0.21 C360.
C480.
C540.
X0.2101 C543.538
X0.2104 C547.073
X0.2108 C550.6

This is what his posted 

O01001
G98 G18
G20
G50 S6000
G53 G0 Y0.
G53 X0.
G53 Z0.

(2D Pocket3)
T202
M154
G28 H0.
G98
G97
P11999 M133
G54
M8
G19
M15
G0 C0.
M14
G0 Z-1.392
X2.7 Y-0.0889
X1.9
G1 X1.7625 F124.0979
G97
P12000 M133
X1.7436 Y-0.0875 Z-1.3916
X1.7264 Y-0.0835 Z-1.3902
X1.7127 Y-0.0773 Z-1.3877
X1.7036 Y-0.0697 Z-1.3842
X1.7 Y-0.0614 Z-1.3798
G3 X1.6783 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.6566 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.6349 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.6131 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.5914 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.5697 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.548 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.5263 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.5046 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.4829 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.4612 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.4394 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.4177 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.396 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.3743 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.3526 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.3309 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.3092 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.2875 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.2657 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.244 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.2223 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.2006 Y-0.2834 Z-1.2502 J-0.0749 K-0.1282
X1.1789 Y-0.0614 Z-1.3798 J0.1484 K-0.0007
X1.1572 Y-0.0601 Z-1.1227 J-0.0736 K0.1289
X1.1355 Y-0.2834 Z-1.

[johnswetz1982]

You probably have "Force Polar" or something similar turned on in the post options.

[Anonymous]

I made a counterbore in X axis plus part of the model, downloaded Haas ST10y post and produced output with Y axis.

I then reversed X axis orientation in setup so that counterbore is in negative X axis of model, it still produced Y output.

Your code is in XCZ mode and I can duplicate that by turning off Y axis in post and not using polar mode.

Your code doesn't show G112 at the top so polar mode is not active.