- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
I recently re-installed the Mac version of AutoCad LT 206 because the existing installation was unable to launch the application. It gets stuck in the initial screen. When at toggle Force Quick it shows the application in red with the message "Not Responding"
Please advise on possible motives for the above.
I am current in my monthly rental fee and my Mac Version is Yosemite 10.10.5
Thank you for your assistance
Rolando
¡Resuelto! Ir a solución.
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
Hi Ronaldo,
You may have to try clean uninstall of AutoCAD :
https://knowledge.autodesk.com/support/autocad-for-mac/troubleshooting/caas/sfdcarticles/sfdcarticle...
Than try to install it again.
Maxim
Do you find the posts helpful? "LIKE" these posts!
Have your question been answered successfully? Click 'ACCEPT SOLUTION' button.
Maxim Kanaev
Architect
MARSS
Etiquette and Ground Rules of Autodesk Community
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
I would recommend the following:
- Clean uninstall as suggested
- Download your product from the virtual agent
- Apply all service packs
Please post back in the thread and let me know if you are able to try the above suggestions.
Thanks.

Sarah Emmsley
Technical Support Specialist
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
I have OS El Captain V 10.11.1
I have downloaded the student version of Maya twice. After this:
It says "done" and nothing happens!! I don't know where it goes but it's not progressing. I am about to throw it out of the window. I also have HW due tomorrow on Maya. So annoying.
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
I have downloaded from virtual agent. The same thing occurred. I don't have any walls up. I have enough space. I just don't understand what is happening.
- Marcar como nuevo
- Favorito
- Suscribir
- Silenciar
- Suscribirse a un feed RSS
- Resaltar
- Imprimir
- Denunciar
Hi,
This is AutoCAD for Mac Forum, you can ask about Maya here:
http://forums.autodesk.com/t5/maya-forum/bd-p/area-b201
Installation forum is here:
http://forums.autodesk.com/t5/installation-licensing/bd-p/24
Maxim
Do you find the posts helpful? "LIKE" these posts!
Have your question been answered successfully? Click 'ACCEPT SOLUTION' button.
Maxim Kanaev
Architect
MARSS
Etiquette and Ground Rules of Autodesk Community