Inventor General

Inventor General

Valued Contributor
Posts: 90
Registered: ‎10-08-2006
Message 1 of 5 (367 Views)

Stress analysis - deflection of a steel block

367 Views, 4 Replies
11-19-2012 03:21 AM

HI

Is it possible to calculate the deflection a steel block will get, just form it one weight

Just use standard steel material, it is only supported at the end.

Regards

Henrik

Product Support
Posts: 181
Registered: ‎06-02-2010
Message 2 of 5 (328 Views)

Re: Stress analysis - deflection of a steel block

11-23-2012 07:11 AM in reply to: hlo

Yes, it is possible. I assume you want to place the Weight positioned along the bar at a set distance.

You can do this by splitting the face with either a circle or rectangle and placing your force there.

I have attached an example. Hopefully I have understood your question.

Jon.

Jon Dean

*Expert Elite*
Posts: 3,634
Registered: ‎11-13-2006
Message 3 of 5 (311 Views)

Re: Stress analysis - deflection of a steel block

11-23-2012 11:58 AM in reply to: jon.dean

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11
Valued Contributor
Posts: 90
Registered: ‎10-08-2006
Message 4 of 5 (289 Views)

Re: Stress analysis - deflection of a steel block

11-25-2012 12:06 AM in reply to: blair

HI

Hi

Thank for reply, i do understand the estimated setup and way to get a bending result

The gravity vector where shout it be placed in this example

Another question regarding the use of split tool, what dose I do to the surface, is it only

marking a round spot and not removing  anything.

Regards

Henrik

*Expert Elite*
Posts: 3,634
Registered: ‎11-13-2006
Message 5 of 5 (272 Views)

Re: Stress analysis - deflection of a steel block

11-25-2012 10:47 AM in reply to: hlo

The Gravity Vector is just that, the direction/vector that gravity will affect the model in question. It doesn't matter which object/edge you select. If an edge is not in the correct direction, you can expand the box and enter a vector using the XZY boxes.

You need to create a sketch on the desired surface and then create a closed loop then exit the sketch. Select the Split Tool command, then the sketch (closed profile) and finally the surface in question.

If you wish to apply a load to a given spot/area on a surface, you would be required to use the Split Surface to create a separate surface in which to apply either the force/load or support constrain. Otherwise Inventor will apply the load/constrain to the whole surface face.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 PDSU / Sim Mech 2015 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 335.23
SpacePilot Pro 3.17.7, 6.17., 4.11

You are not logged in.

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Maintenance Subscription Resources

Upgrading to a 2015 product? Make sure to check these out 1st!

Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.