Inventor Fusion

Reply
Active Member
Posts: 6
Registered: ‎05-01-2012
Message 1 of 8 (1,318 Views)
Accepted Solution

Unable to merge two faces- HELP!!

1318 Views, 7 Replies
05-01-2012 09:18 PM

Trying to merge two faces that were at one point in the design process two separate faces, and through tweaking one face to meet the other face it left a line on the face where they should have healed as one face. Dimensions are equal, there is no "step" or difference in elevation for either face, but I can not for the life of me get rid of the lines that separate the two faces. 

 

I have used the merge feature to attempt to merge them, however it will not let me select the faces or click "OK". I'm hoping that there's a really simple solution here- can anyone help? 

 

Problem lines are selected in the image below, shown in blue:

 

2012-05-01 07.01.45 pm.png

Board Manager
schneik
Posts: 585
Registered: ‎04-05-2003
Message 2 of 8 (1,307 Views)

Re: Unable to merge two faces- HELP!!

05-02-2012 12:46 PM in reply to: sean.s.rafferty

Can you select the face and delete it?

 

large.png

Kevin Schneider


15" Macbook Pro Retina - OSX 10.9 in Portland, Oregon


Active Member
Posts: 6
Registered: ‎05-01-2012
Message 3 of 8 (1,303 Views)

Re: Unable to merge two faces- HELP!!

05-02-2012 06:57 PM in reply to: schneik

I can, but it doesn't heal into one face like you'd expect. Instead it just deletes the face and leaves a hole:

 

2012-05-02 06.31.02 pm.png

 

And same story if I delete the other face:

 

2012-05-02 06.40.48 pm.png

 

If i delete both faces it leaves the line:

 

2012-05-02 06.46.45 pm.png

 

Still can't create a single face from the two faces here- HELP!!!

 

 

 

Board Manager
schneik
Posts: 585
Registered: ‎04-05-2003
Message 4 of 8 (1,293 Views)

Re: Unable to merge two faces- HELP!!

05-03-2012 07:43 AM in reply to: sean.s.rafferty

Switch to the "Solids" workspace and try the delete again. Workspaces can change behavior of some commands and delete when in the surface command does a delete where it will open the solid into a surface when it removes the face.

Delete in the solids workspace does a delete and will heal the gap.

 

While we are at it... If you could post the model here we could take a closer look and give you some other ideas. 

 

Kevin Schneider


15" Macbook Pro Retina - OSX 10.9 in Portland, Oregon


Active Member
Posts: 6
Registered: ‎05-01-2012
Message 5 of 8 (1,286 Views)

Re: Unable to merge two faces- HELP!!

05-04-2012 02:19 AM in reply to: schneik

If I do that, it removes large porions of my model, and does not just delete the face and heal to combine into one surface:

 

If I delete the small surface the geopmetry that existed in the red square is deleted with it:

 

2012-05-04 02.12.20 am.png

 

Same if I delete the larger surface, although more of the model is deleted along with this surface:

 

2012-05-04 02.11.15 am.png

 

Cannot provide model for patent/copyright reasons.

Board Manager
schneik
Posts: 585
Registered: ‎04-05-2003
Message 6 of 8 (1,277 Views)

Re: Unable to merge two faces- HELP!!

05-04-2012 02:19 PM in reply to: sean.s.rafferty

OK.

 

...Here is a workaround. It is not pretty but should work.

 

1. From the face with the unwanted seam create an offset workplane 1mm away into the open slot.

2. Create a sketch on this workplane.

3. Project the boundary of the single face you want to create.

4. Extrude the profile from this boundary 2mm into the model, choose join.

5. Delete/hide the work plane.

6. Using press pull, move the new face -1 so that it is now in the correct position.

Kevin Schneider


15" Macbook Pro Retina - OSX 10.9 in Portland, Oregon


Board Manager
schneik
Posts: 585
Registered: ‎04-05-2003
Message 7 of 8 (1,276 Views)

Re: Unable to merge two faces- HELP!!

05-04-2012 02:26 PM in reply to: schneik

I should also say that in a future update this will be MUCH easier to deal with, and hopefully won't happen in the first place.

 

Kevin Schneider


15" Macbook Pro Retina - OSX 10.9 in Portland, Oregon


Active Member
Posts: 6
Registered: ‎05-01-2012
Message 8 of 8 (1,270 Views)

Re: Unable to merge two faces- HELP!!

05-04-2012 06:21 PM in reply to: schneik

Perfect- that worked!! So until an update comes out addressing this, projecting the surface, trimming the unwanted lines, press-pulling and then re-merging the shape back to the model works. Indeed, a few more steps than desired, but gets me out of this dead end! Thanks!!

 

2012-05-04 06.17.22 pm.png

You are not logged in.

Log into access your profile, ask and answer questions, share ideas and more. Haven't signed up yet? Register

Announcements
Welcome to the new Autodesk Community!
If this is your first visit, click here to get started and make the most of the Community. Let us know what you think of the new experience in the Community Feedback Forum.

Need installation help?

Start with some of our most frequented solutions to get help installing your software.

Ask the Community


Inventor Exchange Apps

Created by the community for the community, Autodesk Exchange Apps for Autodesk Inventor helps you achieve greater speed, accuracy, and automation from concept to manufacturing.

Connect with Inventor

Twitter

Facebook

Blogs

Pinterest

Youtube