https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575084#M16848 <P>Not sure, was hoping some staffer would chime in.</P> Tue, 05 Feb 2019 20:07:45 GMT M_Hennig 2019-02-05T20:07:45Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8571699#M16844 <P>Hey there, I use circular arcs for my links as much as possible because of the nice smooth movement, however on anything over, say, .500 distance or so, they are painfully slow. Is there a realistic way of increasing the feedrate of the circular arc movement to maybe that of the skim value? I have never ran across anything.</P> Mon, 04 Feb 2019 16:14:06 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8571699#M16844 M_Hennig 2019-02-04T16:14:06Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575028#M16845 <P>"Lead feed rates" under feeds and speeds in your toolpath settings?</P> Tue, 05 Feb 2019 19:49:01 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575028#M16845 ksorbo6 2019-02-05T19:49:01Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575035#M16846 <P>That only adjust the lead and out, I want those to be same as feed rate, or maybe 90%. I would like the circular arc moves to haul ass.</P> Tue, 05 Feb 2019 19:51:25 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575035#M16846 M_Hennig 2019-02-05T19:51:25Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575079#M16847 <P>Oh my bad, the links. I don't know how and I've wondered that too, why are certain links locked to cutting feed?</P> Tue, 05 Feb 2019 20:06:07 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575079#M16847 ksorbo6 2019-02-05T20:06:07Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575084#M16848 <P>Not sure, was hoping some staffer would chime in.</P> Tue, 05 Feb 2019 20:07:45 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8575084#M16848 M_Hennig 2019-02-05T20:07:45Z https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8578533#M16849 <P><SPAN class="tlid-translation translation"><SPAN>Have you submitted this to Autodesk?</SPAN> <SPAN class="">It will probably be possible to add this condition directly to the postprocessor.</SPAN></SPAN></P> Wed, 06 Feb 2019 23:11:44 GMT https://forums.autodesk.com/t5/powermill-forum/circular-arc-feedrate/m-p/8578533#M16849 rafael.sansao 2019-02-06T23:11:44Z