topic Re: Frozen layer percentage, part (top) result in Moldflow Insight Forum

Frozen layer percentage, part (top) result

Anonymous — Mon, 20 Aug 2018 18:01:56 GMT

I used 3d tetra mesh for insight model. How can I see Frozen layer percentage, part (top) result ? I only see Frozen layer fraction, but can not see Frozen layer percentage, part (top).

Re: Frozen layer percentage, part (top) result

mppkumar — Tue, 21 Aug 2018 15:13:57 GMT

Frozen layer percentage, part (top) result is available only for mid-plane and DD. since you have used 3D mesh this result won't be available

Plz refer the list of available results based on mesh types in the below link

http://help.autodesk.com/view/MFIA/2019/ENU/?guid=GUID-077521D7-6F22-4445-8EA7-E010A182E094

Re: Frozen layer percentage, part (top) result

Anonymous — Wed, 22 Aug 2018 13:08:22 GMT

Hello,
I am using Moldflow 2018 to conduct cool+fill+pack+warp analysis. I can't see frozen layer pattern like showing below. The entire section is red (100%).
Can you help ?
Thanks a lot,
Joe

[cid:image001.png@01D439F6.F0E9CFE0]
[cid:image002.png@01D439F7.8999CB50]

Re: Frozen layer percentage, part (top) result

mppkumar — Wed, 22 Aug 2018 14:28:59 GMT

Hi Joe

I could not able to see the images, can you reupload it

Re: Frozen layer percentage, part (top) result

Anonymous — Thu, 23 Aug 2018 19:40:44 GMT

I used dual domain mesh to run the model again. But I can't see the change of frozen layer percentage, part (top). It shows 100% at the circled area. What is wrong ?

Re: Frozen layer percentage, part (top) result

raalteh — Fri, 24 Aug 2018 18:04:50 GMT

Hi,

The 'Frozen layer percentage, part (top)' is a Cooling result, which is a simplified view on this. I think you may be looking for a different result though. I suggest you look at the Flow result: "Time to reach ejection temperature" (noting ejection temperature is NOT the same as transition temperature, but it will get you quite close). The

There are a few other ways to look at the result in the flow results: "

Frozen layer fraction', or
look at the temperature result.
- But go to Plot Properites, specify a 'single contour' and use the transition temperature (out of the material data) as the contour value. When you animate this. If you need this as a more time steps for more resolution in the animation you may have to re-run this with more intermediate results (http://help.autodesk.com/view/MFIA/2019/ENU/?guid=GUID-026E5980-A9A6-459D-86CF-E7FD02D49D2D)

Re: Frozen layer percentage, part (top) result

Anonymous — Mon, 27 Aug 2018 12:50:27 GMT

Below is from moldflow online help menu. But I can't get same thing in my model.

This is from middle plate model.

Re: Frozen layer percentage, part (top) result

Anonymous — Thu, 13 Sep 2018 18:40:54 GMT

Hello,
I want to see same frozen layer percentage, part (top) or (bottom) result plot as showing in moldflow online help menu. You

Re: Frozen layer percentage, part (top) result

Anonymous — Thu, 11 Oct 2018 10:51:40 GMT

Hello,

You can use the temperature plot to see the frozen layer at top and bottom of part.

For this you have to scale the plot above the freeze temperature of the material and play the result through time.

At the time where you start to see the glass model, your surface start to freeze i.e. it's temperature goes below the freeze temperature.

How to scale plot :

1. Open the properties of temperature plot.

2. Go to scaling tab and select specified option.

3. Enter the freeze temperature value in "Min" column.

4. Uncheck the extended color dialog box.

Regards,

Krishnakant Garg

@Anonymous wrote:
Hello,
I want to see same frozen layer percentage, part (top) or (bottom) result plot as showing in moldflow online help menu. You