topic Re: I am trying to create threaded concentric hole. in Inventor Forum

I am trying to create threaded concentric hole.

Anonymous — Fri, 11 Dec 2015 11:04:03 GMT

Hi!

Please help me.

I am trying to create threaded concentric hole.

I choose hole ->concentric,

but I can't press ok or apply, and I can't see the thread.

The file is attached

Thanks!

Re: I am trying to create threaded concentric hole.

Frank-Oosterwaal — Fri, 11 Dec 2015 11:59:43 GMT

Hi,

Edit, more detailed answer:

Considering there is a reason why you are doing so but you are working in a multi body environment.

Therefore you have to select the bodies the feature has to be applied on.

Click on solids and select the body (bodies).

Re: I am trying to create threaded concentric hole.

trev4049 — Fri, 11 Dec 2015 11:39:59 GMT

Hi i have just had a quick look at your model, i see your using the split comand try modeling this compont with out using that command.

I will have a better look later if your still having problem.

Regards

Trevor

Re: I am trying to create threaded concentric hole.

Anonymous — Fri, 11 Dec 2015 12:04:30 GMT

@Frank-Oosterwaal,

Yes, this should work,

but it doesn't work

:(((((((((((,

@trev4049

It would be great if you could help me

thanks!

Re: I am trying to create threaded concentric hole.

Frank-Oosterwaal — Fri, 11 Dec 2015 12:12:12 GMT

Hi,

I don't know if you were talking about hole 3 or a new hole, but here's the file with hole 3 and a new hole on the point you showed in the picture.

Re: I am trying to create threaded concentric hole.

mdavis22569 — Fri, 11 Dec 2015 12:13:59 GMT

So use the point that's based on the Concentric

Betreff: I am trying to create threaded concentric hole.

WHolzwarth — Fri, 11 Dec 2015 12:43:11 GMT

Here we go. (2016 file)

The issue was caused by overlapping bodies. Threaded hole existed, but was filled again by the other body.

And you need to zoom in a little closer for seeing that funny M600x6 thread ..

Betreff: I am trying to create threaded concentric hole.

Anonymous — Fri, 11 Dec 2015 15:02:55 GMT

WH,

could you guide me?

What are the steps?

Thank you in advance!

Betreff: I am trying to create threaded concentric hole.

WHolzwarth — Fri, 11 Dec 2015 15:38:43 GMT

Not much to be done.

I've made two boolean join combinations, for getting back only one body.

After that new placement of the threaded hole.

Betreff: I am trying to create threaded concentric hole.

Anonymous — Fri, 11 Dec 2015 16:16:28 GMT

@WHolzwarth,

I don't understand what must be done.

Can you explain in more detail?

Do you have time to create screencast?

https://knowledge.autodesk.com/community/screencast

Thanks!

Betreff: I am trying to create threaded concentric hole.

Anonymous — Sat, 12 Dec 2015 11:54:58 GMT

@Anonymous ?

someone else ?

Is there way to create hole in cylinder without joining main body to the cylinder?

Thanks!

YEAHHHHHH!!!!!!!!!!! I am trying to create threaded concentric hole.

Anonymous — Sat, 12 Dec 2015 12:28:02 GMT

Here is my solution for this issuee:

I removed scetch 12 and hole 4,

then I created new hole.

YEah!!!!!!!!

Re: YEAHHHHHH!!!!!!!!!!! I am trying to create threaded concentric hole.

Anonymous — Sat, 12 Dec 2015 16:07:15 GMT

oops

I can make holes,

but I don't see the thread

Re: I am trying to create threaded concentric hole.

Anonymous — Thu, 15 Mar 2018 07:13:47 GMT

Hello.

It looks like that you did tutorial example.

I practiced same example and meet somewhat similar problem.

OK or apply button was not be activated after I set concentric hole.

What I found was that to activate OK or apply, the procedure for concentric hole should be as follows.

1. click Hole command.

2. from Hole pop up window, choose "Placement: concetric"

2. choose "Plane" from Hole pop up window and select plane from drawing where the concentric hole should be made.

3. choose "concentric Reference" from Hole pop up window and select reference plane from drawing which may be same plane stated above.

4. then follow the instructions as guided by tutorial movie.

then after all setting is done, you will see the activated OK or apply button.

Hope this experiance would be helpful.

Re: I am trying to create threaded concentric hole.

TheCADWhisperer — Thu, 15 Mar 2018 11:30:14 GMT

@Anonymouswrote:

3. choose "concentric Reference" from Hole pop up window and ~~select reference plane~~ from drawing which ~~may be same plane stated~~ above.

No. Concentric reference cannot be a plane. Concentric reference is a cylindrical face or the edge of a circular face.

(Perhaps you mistook the selection of circular edge of end of cylinder as the selection of the planar face of the end of the cylinder?)