topic Re: hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... in Fusion Support Forum https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967703#M94653 yes it is i did convert it to brep but when i try to add a radius to the edges it wont do it because its hollow. went through all the steps on the videos even converting it Tue, 29 Dec 2020 15:57:39 GMT FacebookGroupMember 2020-12-29T15:57:39Z hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967681#M94651 hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what i do the model is hollow . any way to stop this and get a solid model imported Tue, 29 Dec 2020 15:51:09 GMT https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967681#M94651 FacebookGroupMember 2020-12-29T15:51:09Z Re: hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967700#M94652 Can I assume the model is in stl or obj format. If so, you need to lessen the faces and convert it to brep. There is many helpful youtube videos available describing it step by step. Tue, 29 Dec 2020 15:56:09 GMT https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967700#M94652 FacebookGroupMember 2020-12-29T15:56:09Z Re: hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967703#M94653 yes it is i did convert it to brep but when i try to add a radius to the edges it wont do it because its hollow. went through all the steps on the videos even converting it Tue, 29 Dec 2020 15:57:39 GMT https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967703#M94653 FacebookGroupMember 2020-12-29T15:57:39Z Re: hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967846#M94654 Darren Upfield the best would be to use the imported model as a reference only and rather reverse engineer the model you need Tue, 29 Dec 2020 16:56:07 GMT https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9967846#M94654 FacebookGroupMember 2020-12-29T16:56:07Z Re: hi working through fusion . spent yesterday learning to import model but doesnt seem to matter what... https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9984582#M94655 <P>Can you File&gt;Export your *.f3d file to your local drive and then <A href="https://forums.autodesk.com/t5/forums/replypage/board-id/962/message-id/109791" target="_blank" rel="noopener">Attach it here</A> to a Reply?</P> Thu, 07 Jan 2021 13:45:50 GMT https://forums.autodesk.com/t5/fusion-support-forum/hi-working-through-fusion-spent-yesterday-learning-to-import/m-p/9984582#M94655 TheCADWhisperer 2021-01-07T13:45:50Z