topic Re: Sketch is black showing fully constrained but won't lock in Fusion Support Forum

Sketch is black showing fully constrained but won't lock

rogermbown — Thu, 22 Apr 2021 10:30:53 GMT

I'm a little confused. I have a sketch that shows as fully constrained (all lines are black), but won't lock. I have extruded and the software lets me fillet the complete top edge but only partially the bottom.

Any advise please

Re: Sketch is black showing fully constrained but won't lock

TheCADWhisperer — Thu, 22 Apr 2021 10:58:49 GMT

Can you File>Export your *.f3d file to your local drive and then Attach it here to a Reply?

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sun, 25 Apr 2021 10:02:28 GMT

Hi,
File is attached, Thank you.
It is the bottom edge of the Body that won't allow the fillet, although it allowed the entire top edge to fillet (it was extrude from the zero on the plane so don't quite understand why it would allow one edge but not the other? Some of the edges have fillet on the bottom but not the larger one)
On the "not locking" I have checked the geometry and all seems to be OK, but I'm still a rookie, so I'm sure this is something small and a learning curve.

Re: Sketch is black showing fully constrained but won't lock

g-andresen — Sun, 25 Apr 2021 10:22:19 GMT

Hi,

File missing, try again

günther

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sun, 25 Apr 2021 10:33:28 GMT

Should be attached now?

Re: Sketch is black showing fully constrained but won't lock

TheCADWhisperer — Sun, 25 Apr 2021 10:35:25 GMT

Do you actually see it attached?

Must Reply using the web forum, not by email.

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sun, 25 Apr 2021 10:37:28 GMT

Yes, it showed as attached in both mails. Let me try a different browser

Re: Sketch is black showing fully constrained but won't lock

TheCADWhisperer — Sun, 25 Apr 2021 10:39:10 GMT

@rogermbown wrote:
Yes, it showed as attached in both ~~mails~~. Let me try a different browser

I don't believe it. Show screen capture image here...

https://forums.autodesk.com/t5/forums/replypage/board-id/962/message-id/120827

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sun, 25 Apr 2021 10:44:38 GMT

Sorry, my fault, I was replying direct on email not via the forum.

Should be attached now.

Re: Sketch is black showing fully constrained but won't lock

TheCADWhisperer — Sun, 25 Apr 2021 10:57:31 GMT

Sketch1 has an extraneous construction lines and several dimensions that cannot be measured in the real world.

Did you intend Tangency here?

and here...

and here?

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sun, 25 Apr 2021 11:18:07 GMT

Hi, Thank you

One the first 3 points - No I did not intend a tangency, I drew a circle to intersect the end points of the 12mm straight lines and then trimmed the part of the circle that is not wanted

On the 4th point. No I did not intend a tangency. I drew a construction line to the circle diameter and then drew a 3 point arc from that point with the idea to fillet the intersection to create a smooth flow

Re: Sketch is black showing fully constrained but won't lock

TheCADWhisperer — Sun, 25 Apr 2021 11:31:06 GMT

Examine my sketch.

You will have to remove the Tangencies that I assumed.

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Fri, 30 Apr 2021 16:11:43 GMT

Ok Understand now, thank you. I will apply to my original sketch

Re: Sketch is black showing fully constrained but won't lock

rogermbown — Sat, 01 May 2021 08:02:38 GMT

Hi Your solution made sense and helped me understand the tangency issue, i thought I'd try for myself but was not successful. I though I'd make a simpler version without the 12mm straight line and only arcs intersecting one another. Again the sketch is fully black but does not lock. Can you advise why please