topic Re: Adaption of postprocessor jet.cps to add M03 / M05 instead of the comments in Fusion Support Forum

Adaption of postprocessor jet.cps to add M03 / M05 instead of the comments

markus_sc — Sun, 26 Feb 2023 16:15:17 GMT

Hello together,

I am using the jet.cps for creating gcode for my homemade laser maschine. This is working fine so far, but I always have to adapt the created .nc code afterwards manually:

"(TURN ON CUTTING HERE)" replace with "M03;"

"(TURN OFF CUTTING HERE)" replace with "M05"

Now I was a little naive and thought that I can adapt the postprocessor itself so that I dont have to do that manually every time by hand. So I thought it would make sense to just add the commands after the comments in the .cps:

function setDeviceMode(enable) {
if (enable != deviceOn) {
deviceOn = enable;
if (enable) {
writeComment("TURN ON CUTTING HERE");
M03;
} else {
writeComment("TURN OFF CUTTING HERE");
M05;
}

So I saved it under jet_modified.cps and imported it into Fusion 360. But when I now try to create .nc files I get always the message, that the .nc could not be reworked and the file which is resulting is always .nc.failed

Maybe somebody could give me a hint how to adapt the jet.cps in the correct way, that I dont have to replace the comments in the created .nc code everytime manually.

Greetings

Markus

Re: Adaption of postprocessor jet.cps to add M03 / M05 instead of the comments

seth.madore — Sun, 26 Feb 2023 16:38:33 GMT

Would this be acceptable?

N20 G0 X0.4278 Y0.1219 N25 M3 N30 G1 X0.2846 Y-0.0132 F39.37 N35 X0.4043 Y-0.5176 N40 X0.9249 Y-0.6734 N45 X1.3201 Y-0.3004 N50 X1.1947 Y0.2284 N55 X0.674 Y0.3841 N60 X0.2788 Y0.0111 N65 X0.2846 Y-0.0132 N70 X0.4732 Y-0.0696 N75 M5 N80 G0 X-1.3157 Y0.4482 N85 M3 N90 G1 X-1.1398 Y0.3598 F39.37 N95 G3 X-0.9871 Y0.6428 I-0.186 J0.283 N100 X-1.6644 I-0.3387 N105 X-1.1398 Y0.3598 I0.3387 N110 G1 X-1.1511 Y0.5563 N115 M5 N120 G0 X-1.1454 Y-0.3453 N125 M3 N130 G1 X-1.2312 Y-0.1682 F39.37 N135 X-1.597 Y-0.1416 N140 X-1.8169 Y-0.4658 N145 X-1.6461 Y-0.8183 N150 X-1.2554 Y-0.8467 N155 X-1.0355 Y-0.5225 N160 X-1.2062 Y-0.17 N165 X-1.2312 Y-0.1682 N170 X-1.3417 Y-0.3311 N175 M5 N180 G0 X-2.4342 Y-0.2666 N185 M3 N190 G1 X-2.2637 Y-0.1682 F39.37 N195 Y1.315 N200 G2 X-2.2437 Y1.335 I0.02 N205 G1 X2.2437 N210 G2 X2.2637 Y1.315 J-0.02 N215 G1 Y-1.315 N220 G2 X2.2437 Y-1.335 I-0.02 N225 G1 X-2.2437 N230 G2 X-2.2637 Y-1.315 J0.02 N235 G1 Y-0.1682 N240 X-2.4342 Y-0.0697 N245 M5 N250 M30

Re: Adaption of postprocessor jet.cps to add M03 / M05 instead of the comments

markus_sc — Wed, 01 Mar 2023 08:38:14 GMT

Thank you for your effort, this saves me a lot of time...