topic Re: Sketch Slice Bug in Fusion Support Forum

Sketch Slice Bug

sambirchenough — Wed, 19 Apr 2017 20:23:09 GMT

I've had this issue in a few projects where unless I uncheck "slice" before closing a sketch, the whole model stays sliced as if it's a section view.

I don't know why the screencast won't attach but here it is:

https://knowledge.autodesk.com/community/screencast/6630dfd8-755f-4421-b945-f073ca708d38

Re: Sketch Slice Bug

HughesTooling — Wed, 19 Apr 2017 20:48:49 GMT

Don't know if it's the same as I demonstrate in this post, caused by sketching on a plane belonging to a rotated component.

Mark

Re: Sketch Slice Bug

sambirchenough — Wed, 19 Apr 2017 20:59:22 GMT

"Look at" works fine and the sketch plane is on the parent origin plane so I don't think so. Thanks anyway!

Re: Sketch Slice Bug

paul.clauss — Wed, 19 Apr 2017 21:23:34 GMT

Hi @sambirchenough

Thanks for posting! It certainly looks like you are seeing some unintended behavior, but I have been unable to reproduce the issue on my end.

First off, I would check to make sure your graphics drivers are up to date and check to see if this issue still occurs if you limit graphical effects for performance. Also, if you are using any peripheral devices, please ensure that their drivers are up to date.

Does this behavior occur if you do not have the layout grid on?

If you are able to consistently reproduce this behavior with a certain design, please share the design with me and we will continue looking into this issue. Feel free to let me know if you have any questions - I'm happy to help!

Re: Sketch Slice Bug

sambirchenough — Wed, 19 Apr 2017 21:37:38 GMT

@paul.clauss

Thanks Paul. Bug is repeatable on both of my Macs with and without limited graphics (unchecking "use high-res graphics" doesn't change anything either). All graphics drivers / peripheral drivers up to date. One of the several design files I have this issue with attached.

Re: Sketch Slice Bug

mroek — Wed, 19 Apr 2017 22:06:03 GMT

@paul.clauss:

I've also run across this a few times (mentioned in the thread that @HughesTooling referred to), and it is reproducible also with the archive that @sambirchenough attached to this post. Just open "Sketch 2" in the "Top Half"-component and check the slice box, then stop the sketch. The slice stays active, and to turn it off you need to re-edit the sketch and uncheck the slice box.

Re: Sketch Slice Bug

paul.clauss — Wed, 19 Apr 2017 23:09:37 GMT

Hi @sambirchenough, @mroek, @HughesTooling

Thanks for attaching the part! This issue must be dataset specific, as I was able to reproduce the behavior with the Slice Bug file. I have logged an issue with our development team as FUS-32208 and will keep this thread updated when I have new information about this issue to share.

We appreciate you bringing this to our attention! Feel free to let me know if you have any questions.

Re: Sketch Slice Bug

sambirchenough — Wed, 19 Apr 2017 23:14:53 GMT

Thanks @paul.clauss

Just to re-iterate, I've had this bug with a handful of separate design files in various projects.

Re: Sketch Slice Bug

HughesTooling — Thu, 20 Apr 2017 09:50:26 GMT

Here's a workflow that has a repeatable problem with slice. If you create the sketch in the main component then drag it into the top half component you get the problem with slice persisting after closing the sketch.

Here's a screencast, shows creating a sketch in the top half component works without any problems, then show a sketch dragged in causes the problem.

Mark

Re: Sketch Slice Bug

sambirchenough — Thu, 20 Apr 2017 18:04:06 GMT

I get the problem when creating a sketch within an activated component too. The sketch in the previously attached file was created directly within "Top Half."

Re: Sketch Slice Bug

paul.clauss — Fri, 21 Apr 2017 14:59:02 GMT

Thanks @sambirchenough, @HughesTooling

We appreciate you bringing the repeatable workflow to our attention! I will add your comments to FUS-32208 and keep you updated here as we work towards a solution!

Re: Sketch Slice Bug

oyvindTMNSU — Fri, 27 Sep 2019 08:12:05 GMT

I still experience this behaviour...

Re: Sketch Slice Bug

HenryDara — Fri, 06 Dec 2019 23:17:01 GMT

I have also had this problem since using slice view a few months ago. The only way I can get it to "unslice" is to invoke a section view (if there is one) and then uncheck Analysis. Looks like this bug has been around a while, any ideas on progress?

Thanks..Henry