topic Re: Sheetmetal Crash in Fusion Support Forum

Sheetmetal Crash

HughesTooling — Tue, 18 Jun 2019 18:58:02 GMT

Found a repeatable crash. I selected a face for unfolding a sheet metal part but clicked flat pattern by mistake, so I then clicked unfold. This created a flat pattern I didn't want so I clicked undo while in the flat pattern workspace and crash.

I have submitted a couple of crash reports, this is the last one. error report CER_198681887

Mark

Edit I was going to add a screencast but the crash report has my email address. Even though I tried to edit out the end of the screencast the last frame is not edited out.

Re: Sheetmetal Crash

Phil.E — Tue, 18 Jun 2019 19:49:58 GMT

@HughesTooling I can't repeat the crash on a simple test of creating a flat pattern and hitting undo.

Can you share the model, or any other details? There must be something about the data that's a little different than my test files. Another thing about this, it's related to undo, not sheet metal, according to the other reports in the bucket.

Thanks again for posting.

Re: Sheetmetal Crash

TheCADWhisperer — Tue, 18 Jun 2019 20:23:38 GMT

It took me a few attempts to reproduce - but now I can reproduce the issue.

I will post a video when it is done compiling.

CER_198686072 to Autodesk

Re: Sheetmetal Crash

TheCADWhisperer — Tue, 18 Jun 2019 20:26:37 GMT

@Phil.E I am able to reproduce the crash.

Re: Sheetmetal Crash

Phil.E — Tue, 18 Jun 2019 21:26:00 GMT

I'm following the video, still can't find the magic step. What do you think it is?

Re: Sheetmetal Crash

HughesTooling — Tue, 18 Jun 2019 21:37:14 GMT

Preselect the face you want to unfold from, click flat pattern. With the flat pattern dialog open click unfold don't cancel the flat pattern first, this should give you a flat pattern you don't want so click undo.

Mark

Re: Sheetmetal Crash

Phil.E — Tue, 18 Jun 2019 22:17:13 GMT

That's a bit going around the houses... but it works. Got the steps now. Thanks for the report.

Re: Sheetmetal Crash

etfrench — Wed, 19 Jun 2019 07:33:12 GMT

@HughesTooling wrote:

Edit I was going to add a screencast but the crash report has my email address. Even though I tried to edit out the end of the screencast the last frame is not edited out.

I think you'll find the last frame is dropped when it's uploaded, at least it did for me a few months ago.

Re: Sheetmetal Crash

HughesTooling — Wed, 19 Jun 2019 07:56:08 GMT

@etfrench wrote:

@HughesTooling wrote:

Edit I was going to add a screencast but the crash report has my email address. Even though I tried to edit out the end of the screencast the last frame is not edited out.

I think you'll find the last frame is dropped when it's uploaded, at least it did for me a few months ago.

Yes I thought that as well but I tried twice yesterday and even attached the first screencast but when I watched it through the last frame was still there.

Mark

Re: Sheetmetal Crash

TheCADWhisperer — Wed, 19 Jun 2019 12:10:23 GMT

@HughesTooling wrote:
...last frame was still there.

Edit Screencast

Re: Sheetmetal Crash

HughesTooling — Wed, 19 Jun 2019 12:24:08 GMT

Yes I know I edited the video and it left the last frame. In the past it has worked but yesterday it didn't. Someone else reported it a while ago and I figured they'd done something wrong but twice yesterday it didn't work so must be a bit hit or miss.

Re: Sheetmetal Crash

TheCADWhisperer — Wed, 19 Jun 2019 12:41:36 GMT

Keep recording, close the CER and then edit all of that out should work.

So - record beyond anything you want to edit out.