https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8971891#M139548 <P>Follow <A href="https://www.howtogeek.com/194041/how-to-open-the-command-prompt-as-administrator-in-windows-8.1/" target="_blank" rel="noopener">this website instructions</A> to open up a Command Prompt (Administrator) window then type in the commands, given in the article "exactly" as they are written.&nbsp; Once enter, on a a time, press enter to run the command.</P> Sun, 18 Aug 2019 00:21:27 GMT jhackney1972 2019-08-18T00:21:27Z https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8971768#M139547 <P>so I'm going through the solutions offered to one of my issues, but I don't understand what its telling me. It reads "<SPAN>Enter the following command as Administrator to clear Enabled Proxy info." I don't know where to enter that or where I get the key its talking about. Can anyone help?</SPAN></P><P>&nbsp;</P><P><SPAN><A href="https://knowledge.autodesk.com/support/fusion-360/troubleshooting/caas/sfdcarticles/sfdcarticles/Fusion-360-Sufficient-data-not-found-to-switch-to-Offline-mode-Application-will-go-online-now.html?_ga=2.127384842.681066327.1565932196-4028535.1556057274" target="_blank">https://knowledge.autodesk.com/support/fusion-360/troubleshooting/caas/sfdcarticles/sfdcarticles/Fusion-360-Sufficient-data-not-found-to-switch-to-Offline-mode-Application-will-go-online-now.html?_ga=2.127384842.681066327.1565932196-4028535.1556057274</A></SPAN></P> Sat, 17 Aug 2019 21:15:17 GMT https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8971768#M139547 Anonymous 2019-08-17T21:15:17Z https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8971891#M139548 <P>Follow <A href="https://www.howtogeek.com/194041/how-to-open-the-command-prompt-as-administrator-in-windows-8.1/" target="_blank" rel="noopener">this website instructions</A> to open up a Command Prompt (Administrator) window then type in the commands, given in the article "exactly" as they are written.&nbsp; Once enter, on a a time, press enter to run the command.</P> Sun, 18 Aug 2019 00:21:27 GMT https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8971891#M139548 jhackney1972 2019-08-18T00:21:27Z https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8972506#M139549 <P>Thank you.</P> Sun, 18 Aug 2019 18:34:28 GMT https://forums.autodesk.com/t5/fusion-support-forum/i-dont-understand-the-instructions-to-this-solution-to-my/m-p/8972506#M139549 Anonymous 2019-08-18T18:34:28Z