topic Re: Wrong post-code for fanuc in G73 in Fusion Support Forum

Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 16:35:19 GMT

I have a problem.

When i use the cycle chip breaker the post code is not correct becuse don't show me the cycle G73 but all the movements in G0 and G1 to execute the drill cycle.

How i can solve?

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 17:28:42 GMT

Hi @ghost24SBH9Z

open your post in any editor and search case "chip-breaking": Now change below code from

case "chip-breaking": if ((cycle.accumulatedDepth < cycle.depth) || (P > 0)) {

case "chip-breaking": // cycle.accumulatedDepth is ignored if (P > 0) {

save the post and test it carefully.

Thanks,

Re: Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 17:47:30 GMT

This is my post now after your advice but anything change

case "chip breaking": //(cycle.accumulatedDepth < cycle.depth) || if (P > 0) { expandCyclePoint(x, y, z); } else { writeBlock( gRetractModal.format(98), gCycleModal.format(73), getCommonCycle(x, y, z, cycle.retract, cycle.clearance), "Q" + xyzFormat.format(cycle.incrementalDepth), feedOutput.format(F) );

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 17:51:00 GMT

Hi @ghost24SBH9Z ,

Yes. now test it.

Re: Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 17:53:34 GMT

I already tested it but doesn't work

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 18:08:52 GMT

Hi @ghost24SBH9Z ,

Given solution should work. please check with latest fanuc post. Else try with below codes.

case "chip-breaking":

if ((P > 0)) {

expandCyclePoint(x, y, z);

} else {

writeBlock(

(properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(73),

getCommonCycle(x, y, z, cycle.retract),

peckOutput.format(cycle.incrementalDepth),

feedOutput.format(F)

);

}

break;

thanks,

Re: Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 18:07:25 GMT

Post processor engine: 4.5699.0 Configuration path: D:\Programmi_Installati\Utilit� Fusion360\Post-Processor\dmg mori nhx.cps Security level: 1000 Include paths: D:\Programmi_Installati\Utilit� Fusion360\Post-Processor Configuration modification date: Sunday, August 16, 2020 6:06:47 PM Output path: C:\Users\ghost\AppData\Local\Fusion 360 CAM\nc\1.nc Checksum of intermediate NC data: 5c5eeee05591e9985fd472e5af0a1ab3 Checksum of configuration: 6a0fa0ff5b03704d0be19b37ec6e12a5 Vendor url: http://en.dmgmori.com Legal: Copyright (C) 2012-2020 by Autodesk, Inc. Generato da: Fusion 360 CAM 2.0.8809 ... Warning(D:\Programmi_Installati\Utilit� Fusion360\Post-Processor\dmg mori nhx.cps:1526): reference to undefined property properties.type Warning(D:\Programmi_Installati\Utilit� Fusion360\Post-Processor\dmg mori nhx.cps:1526): reference to undefined property properties.type ############################################################################### Errore: ReferenceError: peckOutput is not defined Error at line: 1528 Error in operation: 'Foratura8' Stack dump: onCyclePoint(-397.5,-37.5,207.5)@D:\Programmi_Installati\Utilit￠ Fusion360\Post-Processor\dmg mori nhx.cps:1527 Failed while processing onCycle() for record 386. ############################################################################### Errore: Failed to execute configuration. Stop time: Sunday, August 16, 2020 6:06:58 PM Post processing failed.

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 18:11:05 GMT

Hi @ghost24SBH9Z ,

please share your post processor file (*.cps).

Thanks,

Re: Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 18:14:17 GMT

There is.

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 18:25:44 GMT

Hi @ghost24SBH9Z ,

I though you are using Fanuc generic post. No problem. based on your post i have updated the code.

case "chip-breaking": if ((P > 0)) { expandCyclePoint(x, y, z); } else { writeBlock( gRetractModal.format(98), gCycleModal.format(73), getCommonCycle(x, y, z, cycle.retract, cycle.clearance), "Q" + xyzFormat.format(cycle.incrementalDepth), feedOutput.format(F) ); } break;

Save the post and test it carefully.

Re: Wrong post-code for fanuc in G73

ghost24SBH9Z — Sun, 16 Aug 2020 18:33:00 GMT

ok great!!

Thank you so much for your help.

Now it work.

Re: Wrong post-code for fanuc in G73

KrupalVala — Sun, 16 Aug 2020 18:44:35 GMT

Hi @ghost24SBH9Z ,

Thanks your for your feedback. There was a diff. in cycle name-> chip breaking & chip-breaking. That's why first solution did not work.

IF my answer solve your question, could you please click the "Accept Solution" button ? This helps everyone find answers more quickly!

Thanks,