https://forums.autodesk.com/t5/fusion-design-validate-document/why-can-t-i-sketch-or-do-anything-to-the-bodies-of-my-project/m-p/10099021#M89446 <P>The Press Pull command should do what you want.&nbsp; You may have to adjust it in small increments.&nbsp; Since the helmet is symmetrical, I'd suggest working on one side, then mirroring it.&nbsp; Depending on your slicer, you may need to combine the bodies before printing.</P> <P>&nbsp;</P> <DIV class="iframe-container" style="position: relative; height: 0px; margin: 0px; padding-bottom: 101.563%;"><IFRAME src="https://screencast.autodesk.com/Embed/Timeline/a02ca5b6-3a4d-41d9-bb41-034a03a5e7c0" width="640" height="650" frameborder="0" scrolling="no" allowfullscreen="allowfullscreen" webkitallowfullscreen="webkitallowfullscreen" style="position: absolute; left: 0; top: 0; width: 100%; height: 100%;"></IFRAME></DIV> Sun, 21 Feb 2021 00:53:37 GMT etfrench 2021-02-21T00:53:37Z https://forums.autodesk.com/t5/fusion-design-validate-document/why-can-t-i-sketch-or-do-anything-to-the-bodies-of-my-project/m-p/10098989#M89445 <P>Hey, so still very new to fusion 360 and I don't know what I'm doing all that well. I'm trying to edit this iron man mask to 3D print because, I'm a nerd, however there are a lot of gaps to close in between certain parts of the mask which may be an issue when printing. So I went to press on them and delete however this did not work, and whenever I try to do anything to the body, the software won't let me do anything. What can I do to close these gaps? I've added the fusion file just in case.&nbsp;</P> Sun, 21 Feb 2021 00:23:40 GMT https://forums.autodesk.com/t5/fusion-design-validate-document/why-can-t-i-sketch-or-do-anything-to-the-bodies-of-my-project/m-p/10098989#M89445 19458766 2021-02-21T00:23:40Z https://forums.autodesk.com/t5/fusion-design-validate-document/why-can-t-i-sketch-or-do-anything-to-the-bodies-of-my-project/m-p/10099021#M89446 <P>The Press Pull command should do what you want.&nbsp; You may have to adjust it in small increments.&nbsp; Since the helmet is symmetrical, I'd suggest working on one side, then mirroring it.&nbsp; Depending on your slicer, you may need to combine the bodies before printing.</P> <P>&nbsp;</P> <DIV class="iframe-container" style="position: relative; height: 0px; margin: 0px; padding-bottom: 101.563%;"><IFRAME src="https://screencast.autodesk.com/Embed/Timeline/a02ca5b6-3a4d-41d9-bb41-034a03a5e7c0" width="640" height="650" frameborder="0" scrolling="no" allowfullscreen="allowfullscreen" webkitallowfullscreen="webkitallowfullscreen" style="position: absolute; left: 0; top: 0; width: 100%; height: 100%;"></IFRAME></DIV> Sun, 21 Feb 2021 00:53:37 GMT https://forums.autodesk.com/t5/fusion-design-validate-document/why-can-t-i-sketch-or-do-anything-to-the-bodies-of-my-project/m-p/10099021#M89446 etfrench 2021-02-21T00:53:37Z