topic Re: Creating Vent on a Square in Fusion Design, Validate & Document Forum

Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 02:40:33 GMT

how do i make this instead of cutting all the way through to cut at an angle making a vent? i hope im making sense..

Re: Creating Vent on a Square

hamid.sh. — Fri, 15 Apr 2022 02:47:32 GMT

Do you want to cut along an angled line? Then draw that line in a sketch and use Sweep to cut. Do you want to cut with a tapered angle? Then you have that option in the same Extrude dialogue.

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:01:56 GMT

i want a taper angle but from one side, extrude doesent do that, also sweep cut i have never used im pretty new to designing.. appreciate the help!

Re: Creating Vent on a Square

aliobidi — Fri, 15 Apr 2022 03:06:20 GMT

Hi,

see this

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:09:28 GMT

howdy

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:11:53 GMT

thats not exactly what im looking to do, im going to create a vent for the square hull body on the side profiles, i can show picture example

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:17:23 GMT

i wanted to create scoops for the square hull body on all side faces, example here like the scoops vents for airplanes, basically vent scoop for the square body on all side faces

Re: Creating Vent on a Square

hamid.sh. — Fri, 15 Apr 2022 03:15:18 GMT

Still not sure about your requirement, but I am guessing it's one of these:

Re: Creating Vent on a Square

hamid.sh. — Fri, 15 Apr 2022 03:22:52 GMT

@oystein.l.l wrote:
i wanted to create scoops for the square hull body on all side faces, example here like the scoops vents for airplanes, basically vent scoop for the square body on all side faces

Then I think Sweep is the right tool. Check the one I attached in my previous post. You only need to make a path for the sweep. It can be sketch line, as I did in my file. But also you can do your normal extrude cut and later add a Draft on the faces (again like I did in my file, but only for one face).

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:21:44 GMT

no. i want a angle on bottom and a angle downwards from the top i can draw it 🙂

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 03:25:28 GMT

Re: Creating Vent on a Square

hamid.sh. — Fri, 15 Apr 2022 03:36:59 GMT

@oystein.l.l wrote:

Draw it on a sketch on the side plane and extrude cut it:

Or use Draft twice.

Re: Creating Vent on a Square

g-andresen — Fri, 15 Apr 2022 08:47:18 GMT

Hi,

Targeted references require an insight into the current design.

Please share the file.

File > export > save as f3d on local drive > attach it to the next post

günther

Re: Creating Vent on a Square

TheCADWhisperer — Fri, 15 Apr 2022 12:23:18 GMT

Is something like this what you are attempting to do (see Attached file)?

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 12:23:42 GMT

Yes exactly just both should be symmetrical, looks good how did you do it?

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 12:24:57 GMT

Also how do you get a view inside half the model? Always wondered that!

Re: Creating Vent on a Square

TheCADWhisperer — Fri, 15 Apr 2022 12:34:50 GMT

@oystein.l.l wrote:
Yes exactly just both should be symmetrical,

Not sure what this means?

I just followed your hand sketch.

Can you create another hand sketch that more clearly shows your symmetry Design Intent?

Re: Creating Vent on a Square

TheCADWhisperer — Fri, 15 Apr 2022 12:32:41 GMT

Inspection tab> Section Analysis...

Re: Creating Vent on a Square

TheCADWhisperer — Fri, 15 Apr 2022 12:34:28 GMT

@oystein.l.l wrote:
... how did you do it?

Examine the Timeline.

The history of how I did it is recorded in the Timeline.

Re: Creating Vent on a Square

oystein.l.l — Fri, 15 Apr 2022 12:39:59 GMT

Thank you so much for the help and time to explaining