topic Re: Extruding at an angle? in Fusion Design, Validate & Document Forum

Extruding at an angle?

rnl9t — Fri, 02 Oct 2015 19:20:00 GMT

I swear that in a prior version of Fusion 360, the Extrude command (in Model) had an angle manipulator that let you pick the extrusion direction. Now it seems as though that is missing and right-angle extrusions are the only possible kind. Am I imagining that?

Re: Extruding at an angle?

jeff_strater — Fri, 02 Oct 2015 19:43:33 GMT

there is an angle manipulator in Extrude, but it is for setting the draft angle on the Extrude. It's not really for Extruding at an angle. For that, you need Sweep - define another sketch with a line at the angle you want, then use Sweep to create that angled "extrusion".

Here is the draft angle manipulator:

Jeff Strater (Fusion development)

Re: Extruding at an angle?

michal.vlkovic — Wed, 14 Jul 2021 12:23:54 GMT

Needed to create a sloped face and the Sweep function worked perfectly!

Thank you!!

Re: Extruding at an angle?

sanchitc315 — Wed, 15 Jun 2022 21:02:46 GMT

could you explain this in a sense for soemeone who is completely new to fusion 360 because i just started using this a couple weeks ago.

Re: Extruding at an angle?

jhackney1972 — Wed, 15 Jun 2022 21:15:18 GMT

You did not give any indication on the profile you wanted to Sweep so I just used a simple rectangle. If you have questions after this, please ask.

Just a suggestion, it is much better to create a new Forum post for your particular question rather than piggy back on an old post, especially one that has already been solved. It will draw much more attention and a quicker response.

The Model I used in the Screencast is attached. Be sure to mark this post "As Solution" if it answers your question.

Re: Extruding at an angle?

sanchitc315 — Wed, 15 Jun 2022 23:35:49 GMT

Kay, so didn't help, but I will do what you suggested and make a new Forum post for this and go into more detail about the problem I am having. Thanks for trying though, also, just send it as a quick reply, but how do I mark the post "As Solution" as you described above? I'm new to this so I am just a little bit confused.

Re: Extruding at an angle?

jhackney1972 — Thu, 16 Jun 2022 00:25:31 GMT

So why did it not help? I demoed the exact thing you as Jeff Strater to do. Anyway, since it did not help you, you do not need to mark Accept Solution because it did not solve your issue or question. If you do get an answer and it suits your needs, it is good practice to select the Forum post, that gave you the answer, and click the icon shown below. If you get more than one person responding with good answers, you can click Accept Solution for more than one.

Re: Extruding at an angle?

sanchitc315 — Thu, 16 Jun 2022 01:30:28 GMT

Guess my problem wasn't what this one was describing. From initial looks, it looked different but I don't want to twist the profile. As for the accept solution issue, I can't find it. It isn't showing up on my end. I inserted a screenshot along with this reply and other than the accept solution icon that was in your screenshot, I can't find anything.

Re: Extruding at an angle?

g-andresen — Thu, 16 Jun 2022 08:15:04 GMT

Hi,

@sanchitc315 wrote:
I can't find it. It isn't showing up on my end.

This appears only for the opener of the thread.

günther

Re: Extruding at an angle?

gordonjosephrobinson — Tue, 25 Oct 2022 18:05:58 GMT

Thank you so much for that video it was extremely helpful!

Re: Extruding at an angle?

dclaar — Thu, 11 May 2023 17:29:18 GMT

Thanks, 'define another sketch with a line at the angle you want, then use Sweep to create that angled "extrusion"' worked great! For some reason, I'd had trouble getting Sweep to work before (don't remember why), but this made it really clear and easy.

Re: Extruding at an angle?

nadovich — Fri, 19 Jul 2024 22:50:33 GMT

Sweep doesn't have the handy start and end options that extrude has. So if you just want to "extrude at an angle" per the OP, generally speaking, I think there is some extra work to get to where you were with extrude. At least that's what I needed in order to put a slight tilt angle to a countersink done with a simple extrude that had a start offset. I had to construct a plane for the path of the extrusion. Construct the path itself. Construct a normal offset plane to enter the start offset, create a sketch in this plane, project the profile to the constructed start sketch, THEN I could use sweep. One operation turned into ten, just to extrude at an angle.