topic Re: Press Pull Odd Behavior in Fusion Design, Validate & Document Forum

Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 05:30:07 GMT

Hello

I am having a problem with push/pull in a tutorial. Attached is a screen capture. Please can you help. I am sure I am doing something wrong.

Re: Press Pull Odd Behavior

saito.kh — Mon, 26 Jun 2017 08:18:26 GMT

Hello @Anonymous,

Thank you for posting in the community!

I am sorry to hear that. Can you please let me know which tutorial you are trying?

Since I could take a closer look at your problem on my machine, would you mind sharing your design with me?

I would be able to have your design on this thread or in a private message, either by attaching the file or creating a public link - see the below how to create the public link:

https://knowledge.autodesk.com/support/a360/troubleshooting/caas/sfdcarticles/sfdcarticles/How-to-share-a-Fusion-360-design.html#mtc-english

It would be also appreciated if you would record how you operated by Screencast; this would help me troubleshoot this behavior!

Thanks!

Re: Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 11:10:05 GMT

Hello,

thanks for replying to my problem.

The tutorial is from Lars Christensen.

I folowed the tutorial exactly as he did, but dont have the same result.

Attached is a picture with lars giving the tutor. It is on youtube. Perhaps his version is older?

Re: Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 11:35:19 GMT

Hi @Anonymous

I went through the tutorial.

I think version is not a problem.

I couldn't understand what exactly the problem is ,from the screen shot.

Can you specify exactly what you weren't able to do?

Re: Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 12:06:37 GMT

Hello
Yes the front pipe is red and has lines through it. Push/pull dies not want to extrude. It is supposed to be 28 mm but does not go beyond what is shown in the picture. Why is it red? It must be a fault. I did a fee repeats of the tutorial snd get the same. I also tried extruding from the front and get the same result. It is almost as if only can have one pipe?

Re: Press Pull Odd Behavior

wilkhui — Mon, 26 Jun 2017 12:45:44 GMT

Hi Andre, welcome to the forum!

Are you able to attach your file as @saito.kh mentioned?

Sometimes a small, unintended action can lead to unexpected behaviour and being able to look through your file will allow us to discount that.

Cheers,

Indy

Check out this Screencast: Push/Pull

Anonymous — Mon, 26 Jun 2017 12:55:20 GMT

Hi,

You might be interested in this Screencast:
Push/Pull
Hello,
I am frustrated with this. the extruder on the front face worked 100%, now I tried doing the same on the side of the box and it does not want to
perform the extrude. it shows red .Must be something I am doing wrong.
I followed Lars Christensen tutorial exactly up to this point.
http://autode.sk/2tMpzsi

-------------------------------------------------
Capture and Share Your Expertise
Autodesk Screencast lets you capture your workflows to easily create powerful and
engaging learning materials. For more information visit:
https://screencast.autodesk.com/

Re: Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 13:07:48 GMT

Hello
I sent a screen cast.

Hope you could assist please

thank you

Re: Press Pull Odd Behavior

wilkhui — Mon, 26 Jun 2017 13:11:36 GMT

Hi Andre, thanks for sending the video, it helps!

Can you also attach the .f3d export of your file?

Indy

Re: Press Pull Odd Behavior

HughesTooling — Mon, 26 Jun 2017 13:47:06 GMT

Do you have a section analysis enabled? I have seen similar if you use slice in a sketch and leave it enabled when you close the sketch as well.

Mark

Re: Press Pull Odd Behavior

Anonymous — Mon, 26 Jun 2017 14:00:36 GMT

Hello,
Will have a look if it is enabled. But never used it before.

Re: Press Pull Odd Behavior

HughesTooling — Mon, 26 Jun 2017 14:29:45 GMT

Looking at your screencast you have an analysis folder in your browser, it is only created if you have a section analysis in your design so I suspect that's the problem.

Here's your screencast and you can see the section analysis folder.

Mark

Re: Press Pull Odd Behavior

saito.kh — Tue, 27 Jun 2017 02:14:27 GMT

Hi @Anonymous, @HughesTooling, and @wilkhui,

Thank you for all the inputs and updates! Glad to know this was resolved.

Cheers,

Re: Press Pull Odd Behavior

Anonymous — Tue, 27 Jun 2017 02:58:48 GMT

Thank you for your help. I am sure I will need your expertise in future.