topic Re: Adding deep texture to shape in Fusion Design, Validate & Document Forum

Adding deep texture to shape

sofia — Thu, 30 Jan 2020 12:22:16 GMT

Hi,

I am going to add a texture keeping the outer measurements of the shapes. I changed the profile and it works fine using the sweep command/loft command but I can't get the ends right. I assume I should try to elongate the centreline (for the ring) and the path+rail (for the U shape) following the half sphere but can't figure out how to. Please see images on where I am stuck and also desired look on ends.

The continues shape (without ends) won't loft even though I have projected intersected points to make sure all curves are touching the profiles. Any advice on this? Image attached.

Many thanks,

Sofia

Re: Adding deep texture to shape

TrippyLighting — Thu, 30 Jan 2020 15:42:19 GMT

Aside form the online image viewer function being broken at the moment, it is usually much better to embed images into a post instead of attaching them.

That can easily be active using the large camera button in the menu bar above the text field in the post editing dialogue:

Re: Adding deep texture to shape

jeff_strater — Thu, 30 Jan 2020 15:59:35 GMT

you might have to do the ends as a series of lofts, rather than a single loft.

However, I would be tempted to do this as a Form/T-Spline body. It seems pretty well suited to this kind of shape.

Re: Adding deep texture to shape

TheCADWhisperer — Thu, 30 Jan 2020 16:46:29 GMT

Can you File>Export and then Attach your *.f3d file(s) here?

Re: Adding deep texture to shape

sofia — Mon, 03 Feb 2020 10:33:00 GMT

Please see embedded images @TrippyLighting

Re: Adding deep texture to shape

sofia — Mon, 03 Feb 2020 16:30:27 GMT

Please ignore the question regarding the closed shape, was just a matter of keep trying and rebuilding the same thing.

So for the u-shape I would think the best would be to have one rail going inside the half sphere and the other on the outside of the half sphere meeting at a point (both being connected to the other rails ) before doing the loft/sweep and similar for the other open shape. But can’t figure out how to make those rails..

All best,

Sofia

Re: Adding deep texture to shape

TrippyLighting — Mon, 03 Feb 2020 19:33:52 GMT

Beautiful hand sketches!

I think I would model this as a T-Spline and probably also star with the model in Blender. In Blender I would model this as a straight piece and then use a curve modifier to bend it into shape.

Re: Adding deep texture to shape

sofia — Tue, 04 Feb 2020 10:54:37 GMT

Thank you @TrippyLighting !

These will be updates of the ones I have made that are smooth so therefore it would be nice if I can use the same inputs as much as possible, so they end up as coherent as possible. Is there no way to extend the rails?

Kind Regards,

Sofia

Re: Adding deep texture to shape

TrippyLighting — Tue, 04 Feb 2020 13:16:49 GMT

Without access to the design there is not much we can do 😉

Re: Adding deep texture to shape

sofia — Sun, 09 Feb 2020 17:44:16 GMT

I got some help using another CAD program but it would be nice to know for other future designs if there is a straight forward way to do it. I have attached the file for the open ring.

Kind Regards,

Sofia

Re: Adding deep texture to shape

TrippyLighting — Thu, 25 Jun 2020 00:52:11 GMT

Looks like I totally dropped the ball on this thread.

I did this by tinkering around in Blender for maybe 30-45 minutes.

Imported into FUoisn 360 as a quad mesh, converted to T-Splines and rendered.

Re: Adding deep texture to shape

sofia — Tue, 30 Jun 2020 10:21:12 GMT

Thank you @TrippyLighting , doesn't seem all that easy but good to know for the future and also how to combine the programs!