topic Re: Dynamic Block: Stretch in BOTH directions in Dynamic Blocks Forum

Dynamic Block: Stretch in BOTH directions

Anonymous — Wed, 07 Mar 2007 17:10:06 GMT

Is it possible to have a dynamic block stretch in both directions based on a center point? If so, how?

Thanks in advance.

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Wed, 07 Mar 2007 18:14:51 GMT

use 2 stretch actions but in properies make it stretch in the opposite direction

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Wed, 07 Mar 2007 18:15:24 GMT

you would probably want to post this in the dynamic block group

pat

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Wed, 07 Mar 2007 20:28:26 GMT

2 linear parameters, 1 grip on one, no grips on the other, chain
actions=yes, show=no
2 stretch actions, 2nd stretch action set angle offset to 180

Matt

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Wed, 07 Mar 2007 20:39:28 GMT

Overkill alert! 🙂 How about one linear parameter, set base to Midpoint.
Two stretch actions, either associated with the same end and one with angle
offset of 180, or associated one to each end of the linear parameter.

"Matt Kolberg" wrote in message
news:5511164@discussion.autodesk.com...
2 linear parameters, 1 grip on one, no grips on the other, chain
actions=yes, show=no
2 stretch actions, 2nd stretch action set angle offset to 180

Matt

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Thu, 08 Mar 2007 21:42:50 GMT

Yours is certainly the better solution on retrospect.

Matt

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Fri, 09 Mar 2007 15:34:11 GMT

I just try to avoid chaining parameters whenever possible. Too complicated.
:-)

"Matt Kolberg" wrote in message
news:5512756@discussion.autodesk.com...
Yours is certainly the better solution on retrospect.

Matt

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Fri, 09 Mar 2007 15:45:40 GMT

I don't like chaining dimensions, cause it never works the way I need or
want it to. In fact, it just doesn't work period for me.

--
Brian MacDonald

"Kate M" wrote in message
news:5513524@discussion.autodesk.com...
I just try to avoid chaining parameters whenever possible. Too complicated.
:-)

"Matt Kolberg" wrote in message
news:5512756@discussion.autodesk.com...
Yours is certainly the better solution on retrospect.

Matt

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Mon, 20 Aug 2007 16:09:47 GMT

Hi Matt,
I have been following "stretching from the midpoint." I have been trying to develop a window block that would stretch from the midpoint. Your approach works exactly the way I would like mine to. (There is some kind of bug in AutoCAD 2007 that prevents me from accurately using the midpoint instead of startpoint for a stretch.) I developed a block comparing what you have done. I am attaching the dwg for you to look at. I know I am missing something simple. If you could look at it I would greatly appreciate it. Mel

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Sat, 06 Dec 2008 12:49:11 GMT

Picture a Kitchen Cabinet front to stretch. 1 Linear parameter @ width of cabinet. 1 stretch with distance mult .5 1 stretch with DM .5 & Angle offset 180. this moves the sides. 1 Move DM .25 1 Move DM.25 AO 180. This move handles and door details. Nothing chained

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Tue, 24 Jul 2012 05:13:40 GMT

All,

I am trying to stretch in three directions, I have tried using chain actions but to no avail.

I have attached my attempted block, all I want to do is stretch one distance and have that stretch action work with the two chained distances to make a uniform stretch. i.e. all the distances will be that same length, but at the moment my stretch is just stretching the chain actions in the same direction as the primary stretch rather than stretching each uniformly outwards.

I hope I have made enough sense for someone to provide me with a solution.

Any help is much appreciated.

Warm Regards,

Shaun

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Sun, 29 Mar 2015 14:12:16 GMT

Shaun,

I'm a little late on an answer, but for posterity, you would use one distance parameter and three stretch actions. I used the distance going from the center to the top leg. Then did a stretch action of that leg. Then did a stretch action of the lower left leg, referencing the same distance parameter. But I changed the rotation angle to 120. Then I did a stretch action on the lower right leg and changed its angle to 240. Works like a charm. I've uploaded your file with the changes I made, although I'm sure you solved it long ago.

Bill

Re: Dynamic Block: Stretch in BOTH directions

ndawsonmccann — Thu, 19 Nov 2015 15:11:37 GMT

I got this to work after several attempts. There are a few extra notes I added to the steps.

The left stretch action without the grip should have (Show Properties = No) and (Chain Actions = Yes) (Angle = 180). This action should show (Selection set = 1 objects).

The right stretch action with the grip should have (Show Properties = Yes) and (Chain Actions = No) (Angle = 0). This action should show (Selection set = 3 objects).

-Nick

Re: Dynamic Block: Stretch in BOTH directions

CathyHarron — Fri, 10 Mar 2017 18:20:28 GMT

"One linear parameter, set base to Midpoint, two stretch actions" - Wow.... This was exactly what I needed! 🙂 I just didn't think of putting 2 actions to the same parameter! That's brilliant! 🙂 I've put parameters and actions inside other parameters and actions but... my shortsightedness was to not think of putting two actions to the same parameter! You've opened up a whole new world for me! Thanks a bundle!!

Re: Dynamic Block: Stretch in BOTH directions

Emmsleys — Sat, 01 Apr 2017 00:04:55 GMT

Thanks for posting back in thread to validate that one of the post's helped resolve your issue. I don't think the OP will come back to the thread so I can go ahead and mark @ ndawson post.

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Thu, 04 Apr 2019 11:08:44 GMT

You can also do as below method

Add 1 Linear Parameter with 2 grips, Change parameter settings in properties/Misc = (Base Location = Midpoint)

add 2 Stretch action on both ends. it will works fine

see the attached file

Re: Dynamic Block: Stretch in BOTH directions

Libbya — Thu, 04 Apr 2019 14:37:23 GMT

@ndawsonmccann wrote:

I got this to work after several attempts. There are a few extra notes I added to the steps.

The left stretch action without the grip should have (Show Properties = No) and (Chain Actions = Yes) (Angle = 180). This action should show (Selection set = 1 objects).

The right stretch action with the grip should have (Show Properties = Yes) and (Chain Actions = No) (Angle = 0). This action should show (Selection set = 3 objects).

-Nick

That's silly complicated. Don't chain anything. Don't mess with the angle offsets or distance modifiers.

Linear parameter with base point mid and a stretch on each endpoint. Done.

Re: Dynamic Block: Stretch in BOTH directions

Anonymous — Fri, 27 Mar 2020 14:54:42 GMT

this is a perfect solution to the question at hand

Re: Dynamic Block: Stretch in BOTH directions

thomas — Wed, 17 Mar 2021 18:01:05 GMT

Would you have a DWG example of this? For the life of me I can't recreate it

Re: Dynamic Block: Stretch in BOTH directions

Libbya — Wed, 17 Mar 2021 18:11:28 GMT

Thomas, rather than asking someone else to come up with an example DWG to post, it might be better for you to post your block attempt and others could let you know how to correct it.