topic Corridor Section Editor View is Gone in Civil 3D Forum

Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 14:27:13 GMT

My section view is not showing up when I try to open the Section Editor for my corridor. How can I get it back?

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 14:49:34 GMT

While you have the Section Editor open:

Section Editor tab > View Tools panel > Viewport Controls.
Set the "Layout" (on the left) to show the appropriate number of views.
Set the Viewports (on the right) assigning each VP as desired.

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 14:52:38 GMT

I have tried changing the viewport configuration in the section editor and it does not help

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 14:53:51 GMT

Here is a screenshot of my viewport configuration

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 15:32:54 GMT

Try changing the viewport configuration to show only the PLAN VIEW. Then change it back to showing both. This SHOULD re-initialize the VP settings.

If that doesn't work, change the config to only the Plan view and CLOSE the section editor. Now re-open the section editor and change the VP configu back to showing the section view.

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 15:38:51 GMT

When I try changing the viewport configuration to only show the plan view I receive an error message that says one viewport must be set to Section view. Here is a screenshot of the error message.

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 16:26:46 GMT

Have you tried closing and restarting the Section Editor yet as previously suggested?

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 17:08:35 GMT

Yes I have closed out of the Section Editor and when I reopen it the view is still messed up. I have even closed the drawing and reopened it but to no avail

Re: Corridor Section Editor View is Gone

MikeEvansUK — Fri, 04 Nov 2016 17:34:54 GMT

I assume that this is not just at a single corridor section but displays like this in all?

I would try sectioning the corridor, do the sections display correctly? If not you may have a rogue target or assembly spiking to infinity..

Other ideas.

Turn off any Hardware acceleration.

Audit the file, sometimes we get problems with stuff (Duplicate ID's etc) on the Fly - Seeing this more and more in R2016.

please turn all layers on and thaw all layers. (doubt if that will help but something may be wrong).

Adjust the start point of the corridor a bit then re-build it.

Check your UCS settings maybe for some reason the corridor is not correctly aligned to WORLD.. - UCS, Plan.

Otherwise, it could just be a corrupt file. Try inserting it into a fresh template to see if this Fixes it.

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 18:31:15 GMT

Following is a screenshot taken from Section Editor on my PC. Compare this to the OP's screenshot. See the difference between the nav wheels? It appears that the Section Editor is actually turning the VP iternally for the purposes of showing the sections. But OP's VP is not doing this.

Edit: I was also unable to reproduce having the VP not show the grid lines by turning layers off.

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 18:29:36 GMT

I believe my file has been corrupted. I created a data shortcut for the corridor and created a reference of it in a new drawing and the section editor works perfectly fine. Is there a way to promote the corridor into this new drawing? When I try to promote it from the data shortcuts the "promote" button is greyed out.

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 18:34:09 GMT

@Anonymous wrote:

I believe my file has been corrupted. I created a data shortcut for the corridor and created a reference of it in a new drawing and the section editor works perfectly fine. Is there a way to promote the corridor into this new drawing? When I try to promote it from the data shortcuts the "promote" button is greyed out.

The more we've dug into this issue, the more I've come to think the same thing. Have you tried running the Audit command on the original file? How about RECOVER?

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 18:41:50 GMT

Ran Audit and there were 114 errors but after it fixed them the Section Editor view is still messed up

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 18:46:39 GMT

Now that you've run the Audit command, try closing the Section Editor and re-opening it again. And in fact, I think I would:

Close Section Editor.
Run the Audit command (and let it fix errors).
Save the dwg file.
Close the dwg file.
Re-open the dwg file.
Run the Audit command (without FIX enabled) just to confirm there are no more errors.
If no errors found, Re-open the Section Editor. If it did find errors, go back to step 2 and repeat until there are no errors found.

Re: Corridor Section Editor View is Gone

Anonymous — Fri, 04 Nov 2016 19:05:38 GMT

Did all these steps until no errors were found when running Audit and the Section Editor view still does not work

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 20:02:35 GMT

Post a copy of your audited/fixed file and someone should be able to investigate more.

Re: Corridor Section Editor View is Gone

doni49 — Fri, 04 Nov 2016 20:23:58 GMT

ALSO: what version (including SP#) are you using?

Re: Corridor Section Editor View is Gone

j_schroeder1 — Wed, 15 Aug 2018 21:32:38 GMT

Just want to ensure due diligence and give my 2 cents. I had the same issue occuring. The problem was a subassembly link targeting a profile and alignment. It couldn't find the profile and was targeting to zero. So my section view grid in section editor was displaying elevations in the 450' ballpark instead of 900'. This seems like an obvious no-brainer, but it was giving me fits so I figured I would share just in case.

Re: Corridor Section Editor View is Gone

DArmstrongDOT — Wed, 28 Jul 2021 00:34:40 GMT

We had a C3D 2020.6 user who also experienced a blank Corridor Section Editor, CSE, viewport. After a couple hours of troubleshooting, I noticed that the current Layer was locked. Once unlocked and the CSE reopened, all was well again.

Another Current Layer related issue is the CSE grid displaying with an odd linetype. We discovered that the Section Editor grid inherits/uses the linetype assigned to the current AutoCAD layer. Once the current layer was assigned a continuous linetype, the grid appeared normal.

Re: Corridor Section Editor View is Gone

Ronczez — Thu, 21 Jul 2022 10:24:14 GMT

I had similar Issue.

In my case turnoff all freezeed layers was the solution.