<?xml version="1.0" encoding="UTF-8"?>
<rss xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:taxo="http://purl.org/rss/1.0/modules/taxonomy/" version="2.0">
  <channel>
    <title>topic Finish allowance in Fusion Manufacture</title>
    <link>https://forums.autodesk.com/t5/fusion-manufacture/finish-allowance/m-p/7243660#M34558</link>
    <description>&lt;P&gt;In other CAM software I have used there is Finish Allowance. &amp;nbsp;This allows one to over (or under) cut a profile, pocket, etc. &amp;nbsp;For example if your tool doesn't quite make it through the bottom of the part, you might add a positive finish allowance and re-cut that toolpath which would put the tool farther below the bottom, cutting through the material. &amp;nbsp;In another scenario you might need to enlarge a pocketed hole a couple thousandths (due to a cutter being slightly under diameter or something) and rather than go back to modeling and re-size the hole, you can add a finish allowance to over-cut the pocket a bit.&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;
&lt;P&gt;Does Fusion CAM have this feature? &amp;nbsp;I need to both, oversize a hole a tiny bit AND to cut deeper &amp;nbsp;past the bottom of part and in looking at all the parameters I don't see how I could do that.&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;
&lt;P&gt;-Tom&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;</description>
    <pubDate>Fri, 21 Jul 2017 00:28:03 GMT</pubDate>
    <dc:creator>tomae</dc:creator>
    <dc:date>2017-07-21T00:28:03Z</dc:date>
    <item>
      <title>Finish allowance</title>
      <link>https://forums.autodesk.com/t5/fusion-manufacture/finish-allowance/m-p/7243660#M34558</link>
      <description>&lt;P&gt;In other CAM software I have used there is Finish Allowance. &amp;nbsp;This allows one to over (or under) cut a profile, pocket, etc. &amp;nbsp;For example if your tool doesn't quite make it through the bottom of the part, you might add a positive finish allowance and re-cut that toolpath which would put the tool farther below the bottom, cutting through the material. &amp;nbsp;In another scenario you might need to enlarge a pocketed hole a couple thousandths (due to a cutter being slightly under diameter or something) and rather than go back to modeling and re-size the hole, you can add a finish allowance to over-cut the pocket a bit.&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;
&lt;P&gt;Does Fusion CAM have this feature? &amp;nbsp;I need to both, oversize a hole a tiny bit AND to cut deeper &amp;nbsp;past the bottom of part and in looking at all the parameters I don't see how I could do that.&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;
&lt;P&gt;-Tom&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;</description>
      <pubDate>Fri, 21 Jul 2017 00:28:03 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/fusion-manufacture/finish-allowance/m-p/7243660#M34558</guid>
      <dc:creator>tomae</dc:creator>
      <dc:date>2017-07-21T00:28:03Z</dc:date>
    </item>
    <item>
      <title>Re: Finish allowance</title>
      <link>https://forums.autodesk.com/t5/fusion-manufacture/finish-allowance/m-p/7243671#M34559</link>
      <description>&lt;P&gt;Nevermind, I found it. &amp;nbsp;Stock To Leave....&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;
&lt;P&gt;&amp;nbsp;&lt;/P&gt;</description>
      <pubDate>Fri, 21 Jul 2017 00:41:48 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/fusion-manufacture/finish-allowance/m-p/7243671#M34559</guid>
      <dc:creator>tomae</dc:creator>
      <dc:date>2017-07-21T00:41:48Z</dc:date>
    </item>
  </channel>
</rss>

