<?xml version="1.0" encoding="UTF-8"?>
<rss xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:taxo="http://purl.org/rss/1.0/modules/taxonomy/" version="2.0">
  <channel>
    <title>topic Re: 2D contour Tabs  With Lead in /Out in Fusion Manufacture</title>
    <link>https://forums.autodesk.com/t5/fusion-manufacture/2d-contour-tabs-with-lead-in-out/m-p/11954230#M139364</link>
    <description>&lt;P&gt;I am not sure about your direct question (lead-in/out), but when you make the tabs, are you doing them in full solid material?&amp;nbsp; If so, try roughing out a channel up to the top of your tabs before doing the tabs (leave just a finish allowance on the part's walls).&amp;nbsp; You can also try the triangular tabs, they dont plunge straight down.&lt;/P&gt;</description>
    <pubDate>Wed, 10 May 2023 12:33:25 GMT</pubDate>
    <dc:creator>DarthBane55</dc:creator>
    <dc:date>2023-05-10T12:33:25Z</dc:date>
    <item>
      <title>2D contour Tabs  With Lead in /Out</title>
      <link>https://forums.autodesk.com/t5/fusion-manufacture/2d-contour-tabs-with-lead-in-out/m-p/11953945#M139363</link>
      <description>&lt;P&gt;Is it possible to make 2d contour&amp;nbsp; toolpath that makes tabs and use lead in/out when making tab?&lt;BR /&gt;Problem is when tool is going up and down when making a&amp;nbsp; tab it leaves a mark.&lt;/P&gt;&lt;P&gt;&amp;nbsp;&lt;/P&gt;</description>
      <pubDate>Wed, 10 May 2023 10:03:07 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/fusion-manufacture/2d-contour-tabs-with-lead-in-out/m-p/11953945#M139363</guid>
      <dc:creator>morten4MDUW</dc:creator>
      <dc:date>2023-05-10T10:03:07Z</dc:date>
    </item>
    <item>
      <title>Re: 2D contour Tabs  With Lead in /Out</title>
      <link>https://forums.autodesk.com/t5/fusion-manufacture/2d-contour-tabs-with-lead-in-out/m-p/11954230#M139364</link>
      <description>&lt;P&gt;I am not sure about your direct question (lead-in/out), but when you make the tabs, are you doing them in full solid material?&amp;nbsp; If so, try roughing out a channel up to the top of your tabs before doing the tabs (leave just a finish allowance on the part's walls).&amp;nbsp; You can also try the triangular tabs, they dont plunge straight down.&lt;/P&gt;</description>
      <pubDate>Wed, 10 May 2023 12:33:25 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/fusion-manufacture/2d-contour-tabs-with-lead-in-out/m-p/11954230#M139364</guid>
      <dc:creator>DarthBane55</dc:creator>
      <dc:date>2023-05-10T12:33:25Z</dc:date>
    </item>
  </channel>
</rss>

