<?xml version="1.0" encoding="UTF-8"?>
<rss xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:taxo="http://purl.org/rss/1.0/modules/taxonomy/" version="2.0">
  <channel>
    <title>tema tool constantly lifting out of material on MF files en FeatureCAM Forum</title>
    <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8702221#M4424</link>
    <description>&lt;P&gt;I have tried everything I can think of, and no matter what I do, when I create an MF file, the tool is constantly&amp;nbsp; lifting out of the material. it will take a small cut lift up to the rapid plane even though I have retract to plunge clearance marked. I have used minimize tool retract it still does it. I have also tried everything under the milling tab. At this rate what should be faster to run multiple parts is taking three to four times longer per part than if I just ran them individually. Anyone have any ideas?&lt;/P&gt;
&lt;P&gt;Okay so I tried to attach the MF file but apparently you can't attach that file type go figure so I don't know how to show how it is programming it. I have however attached the FM file as of the last try but like I said I have tried a lot of different scenarios without any luck.&lt;/P&gt;</description>
    <pubDate>Tue, 02 Apr 2019 18:49:25 GMT</pubDate>
    <dc:creator>Anonymous</dc:creator>
    <dc:date>2019-04-02T18:49:25Z</dc:date>
    <item>
      <title>tool constantly lifting out of material on MF files</title>
      <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8702221#M4424</link>
      <description>&lt;P&gt;I have tried everything I can think of, and no matter what I do, when I create an MF file, the tool is constantly&amp;nbsp; lifting out of the material. it will take a small cut lift up to the rapid plane even though I have retract to plunge clearance marked. I have used minimize tool retract it still does it. I have also tried everything under the milling tab. At this rate what should be faster to run multiple parts is taking three to four times longer per part than if I just ran them individually. Anyone have any ideas?&lt;/P&gt;
&lt;P&gt;Okay so I tried to attach the MF file but apparently you can't attach that file type go figure so I don't know how to show how it is programming it. I have however attached the FM file as of the last try but like I said I have tried a lot of different scenarios without any luck.&lt;/P&gt;</description>
      <pubDate>Tue, 02 Apr 2019 18:49:25 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8702221#M4424</guid>
      <dc:creator>Anonymous</dc:creator>
      <dc:date>2019-04-02T18:49:25Z</dc:date>
    </item>
    <item>
      <title>Re: tool constantly lifting out of material on MF files</title>
      <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704080#M4429</link>
      <description>&lt;P&gt;Set your vortex z lift to .003. Thats the backfeed micro-lift. Its a non cutting move. Hope that helps.&lt;/P&gt;
&lt;P&gt;It is in the milling tab&lt;/P&gt;</description>
      <pubDate>Wed, 03 Apr 2019 11:51:55 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704080#M4429</guid>
      <dc:creator>zlancy244</dc:creator>
      <dc:date>2019-04-03T11:51:55Z</dc:date>
    </item>
    <item>
      <title>Re: tool constantly lifting out of material on MF files</title>
      <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704602#M4430</link>
      <description>&lt;P&gt;Okay I was trying to go by what the help files were showing and it looked like the larger the Z lift the less it would lift out. I must be misinterpreting what the help files say or they are backwards.&lt;/P&gt;</description>
      <pubDate>Wed, 03 Apr 2019 14:20:18 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704602#M4430</guid>
      <dc:creator>Anonymous</dc:creator>
      <dc:date>2019-04-03T14:20:18Z</dc:date>
    </item>
    <item>
      <title>Re: tool constantly lifting out of material on MF files</title>
      <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704607#M4431</link>
      <description>&lt;P&gt;Oh and thank you so much it worked great&lt;/P&gt;</description>
      <pubDate>Wed, 03 Apr 2019 14:21:08 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8704607#M4431</guid>
      <dc:creator>Anonymous</dc:creator>
      <dc:date>2019-04-03T14:21:08Z</dc:date>
    </item>
    <item>
      <title>Re: tool constantly lifting out of material on MF files</title>
      <link>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8705212#M4433</link>
      <description>&lt;P&gt;Great, glad I could help.&lt;/P&gt;</description>
      <pubDate>Wed, 03 Apr 2019 17:08:35 GMT</pubDate>
      <guid>https://forums.autodesk.com/t5/featurecam-forum/tool-constantly-lifting-out-of-material-on-mf-files/m-p/8705212#M4433</guid>
      <dc:creator>zlancy244</dc:creator>
      <dc:date>2019-04-03T17:08:35Z</dc:date>
    </item>
  </channel>
</rss>

