Ed,
I would like to get some information about your
install process. Do you recall what you selected in the dialog
below?
[img src="@104669"]
Are you connecting to a remote Data Management Server or is everything on
your local system?
Christian Maylath
Autodesk, Product
Design
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"Christian Maylath" <
href="mailto:christian.maylath@NoSpam.autodesk.com">christian.maylath@NoSpam.autodesk.com>
wrote in message
href="news:5142184@discussion.autodesk.com">news:5142184@discussion.autodesk.com...
Ed,
I would like to get some information about your
install process. Do you recall what you selected in the dialog
below?
[img src="@104669"]
Are you connecting to a remote Data Management Server or is everything on
your local system?
Christian Maylath
Autodesk, Product
Design
"Ed Rasmussen" <I have a clean install of IV11
href="mailto:edras@a-concepts.com">
size=2>edras@a-concepts.com> wrote in
message
size=2 ial>news:5141821@discussion.autodesk.com
size=2>...
and Vault5 on my new computer. I was using
IV10 and Vault4 on my old
computer. I backed up my vault on the old
computer and restored it
on the new one. That seemed to go smoothly. My
vaulted files
appear to be there and are ok. However, the new content
center se
ems empty. My files that contain parts from the old content center
are unable to find those parts. There may be some configuration or
setup
that I have not done. I went to the project files and click on
the
configure content center libraries. All the listings are
red. I have not
had any luck getting past this point. Does
anyone have any suggestions or
similar experience? Thank you.
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"Ed Rasmussen" <
href="mailto:edras@a-concepts.com">edras@a-concepts.com> wrote in
message
href="news:5142306@discussion.autodesk.com">news:5142306@discussion.autodesk.com...
Christian,
I believe that I marked that box just as shown in
your email. I am a stand alone user. I don't think that I selected
the "I want to make this computer my ADMS server." Could this cause my
problem? If so, what is the best way to address it? Thanks for the
help.
Ed R
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
"Christian Maylath" <
href="mailto:christian.maylath@NoSpam.autodesk.com">christian.maylath@NoSpam.autodesk.com>
wrote in message
href="news:5142184@discussion.autodesk.com">news:5142184@discussion.autodesk.com...
Ed,
I would like to get some information about your
install process. Do you recall what you selected in the dialog
below?
[img src="@104669"]
Are you connecting to a remote Data Management Server or is everything on
your local system?
Christian Maylath
Autodesk, Product
Design
"Ed Rasmussen" <I have a clean install of
href="mailto:edras@a-concepts.com">
size=2>edras@a-concepts.com> wrote in
message
size=2 ial>news:5141821@discussion.autodesk.com
size=2>...
IV11 and Vault5 on my new computer. I was using
IV10 and Vault4 on
my old computer. I backed up my vault on the old
computer and
restored it on the new one. That seemed to go smoothly. My
vaulted files appear to be there and are ok. However, the new
content
center se ems empty. My files that contain parts from the
old content center
are unable to find those parts. There may be
some configuration or setup
that I have not done. I went to the
project files and click on the
configure content center libraries.
All the listings are red. I have not
had any luck getting past
this point. Does anyone have any suggestions or
similar
experience? Thank you.