Discussion Groups

Simulation Moldflow Insight

Reply
Member
4 Posts
0 Kudos
Registered: ‎12-14-2012

How to check internal stresses of a part in moldflow?

472 Views, 8 Replies
12-14-2012 07:31 PM

How to check internal stresses of a part (after warpage analysis) in moldflow software. Please help me ASAP.

 

Regards

 

M M Keeravani

*Expert Elite*
328 Posts
249 Kudos
Registered: ‎03-18-2009

Re: How to check internal stresses of a part in moldflow?

12-15-2012 06:41 PM in reply to: keeravani786
moldflow will not provide. you need to use external software like ansys, abqus.. etc.. Ask help from moldflow techsupport team.
Madhukeshwar Talwar

FIAT-CHRYSLER ATC, Chennai
mail: madhukeshwart@gmail.com
09600060862
======================================
Please use . Accept as Solution and Give Kudos as appropriate to further enhance these forums. Thank you! .....
Member
4 Posts
0 Kudos
Registered: ‎12-14-2012

Re: How to check internal stresses of a part in moldflow?

12-16-2012 07:16 PM in reply to: madhukeshwart

ThanQ. I will do.

Member
5 Posts
0 Kudos
Registered: ‎12-15-2011

Re: How to check internal stresses of a part in moldflow?

12-16-2012 11:21 PM in reply to: keeravani786
How about checking shear stress? Or is there any way to confirm it with flow temperature? I was also interested in getting some ideas about this?

Thx
Member
4 Posts
0 Kudos
Registered: ‎12-14-2012

Re: How to check internal stresses of a part in moldflow?

12-17-2012 09:39 PM in reply to: w18855

A good response to this question may help us a lot.

*Expert Elite*
328 Posts
249 Kudos
Registered: ‎03-18-2009

Re: How to check internal stresses of a part in moldflow?

12-26-2012 12:37 AM in reply to: keeravani786

Moldflow residual stresses plot will give internal stresses but it is before warpage.

Madhukeshwar Talwar

FIAT-CHRYSLER ATC, Chennai
mail: madhukeshwart@gmail.com
09600060862
======================================
Please use . Accept as Solution and Give Kudos as appropriate to further enhance these forums. Thank you! .....
Active Member
10 Posts
0 Kudos
Registered: ‎03-27-2012

Re: How to check internal stresses of a part in moldflow?

01-02-2013 09:50 PM in reply to: keeravani786

Hi Keeravani,

 

As Madhu said, you can correlate from residual stress result, but this result can be seen only in dual domain and midplane meshes. What type of mesh are you using?

 

Regards,

Ashwin

Contributor
24 Posts
0 Kudos
Registered: ‎12-29-2009

Re: How to check internal stresses of a part in moldflow?

04-08-2013 04:32 AM in reply to: madhukeshwart

Hello ,

 

There is a stress analysis module in moldflow....what  will this calculate ??

Does this require additional license or is it part of performance license ?

 

KLP

Product Support
485 Posts
41 Kudos
Registered: ‎03-23-2009

Re: How to check internal stresses of a part in moldflow?

04-08-2013 05:51 AM in reply to: klp2kor

Hi,
the stress module is available in
Autodesk Simulation Moldflow Insight Premium and
Autodesk Simulation Moldflow Insight Ultimate.

You have some information at:
http://wikihelp.autodesk.com/Simulation_Moldflow/enu/2013/Help/Communicator/0428-Analysis428/0468-St...

It is available for Midplane mesh types.

Regards,
Berndt



Berndt Nordh