Discussion Groups

Simulation Moldflow Insight

Reply
Distinguished Contributor
mayur_dhumal
Posts: 164
Registered: ‎05-05-2011
Accepted Solution

How to Activate 'Mold internal temperature result' in a 3D cool analysis?

213 Views, 6 Replies
06-05-2014 03:52 AM

I have a 3D analysis, but this does not have 'Mold internal temperature result' plot as default neither it is available in 'Create New plot'.

Does anyone have a idea about it?

Please use plain text.
Distinguished Contributor
mayur_dhumal
Posts: 164
Registered: ‎05-05-2011

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 02:16 AM in reply to: mayur_dhumal
I have defined a mold boundary.
Even i have enabled 'Calculate internal mold temperature' from Process settings wizard>Advanced Options>Solver parameters>Cool Analysis & set grid resolution to '20' , 'Temperature, internal mold result' is not generated or not found in New Plot.

As per help it has to be generated.

Thanks,
Mayur
Please use plain text.
Member
inba.oneway777
Posts: 3
Registered: ‎02-25-2014

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 04:14 AM in reply to: mayur_dhumal

Hi,

 

You have to make a moldblock boundary. then only you will get the internal mold temperature results.

Goto Geometry=>Moldsurface=>Moldsurface wizard will open and you have to size the mold outer surface.

After that you have to choose the Mold internal surface in cool solver paramerter settings.

Leave the Grid in default settings. if you want to change the grid location use cutting plane or section.

 

i hope i answered your question.

 

Regards,

Inba

Please use plain text.
Distinguished Contributor
mayur_dhumal
Posts: 164
Registered: ‎05-05-2011

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 04:38 AM in reply to: inba.oneway777
Hi Inba,

I have already fulfilled these conditions, namely:
1) Design mold boundary
2) Click checkbox ' 'Calculate internal mold temperature' & set grid resolution value.
3) Selected 3D Cool (FEM) Analysis with 'Average over Cycle'.
4) Create custom plot

After these conditions fulfilled, i can't get this result plot.
I guess this plot may produced from a Cool Analysis and not from a Cool (FEM), i will cross-check or support may have been called off for this plot.

Thanks,
Mayur
Please use plain text.
Distinguished Contributor
mayur_dhumal
Posts: 164
Registered: ‎05-05-2011

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 04:53 AM in reply to: mayur_dhumal
Hi Inba,

Got the solution!
I was performing point number 3) wrong, i should have chosen to perform Cool Analysis instead of Cool (FEM).
Even help document also states correctly,just confirmed.

Thanks for your reply.
Mayur

Please use plain text.
Member
inba.oneway777
Posts: 3
Registered: ‎02-25-2014

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 04:59 AM in reply to: mayur_dhumal

Hi Mayur,

 

No need togo for Cool(FEM). Norema cool analysis you will get it.

 

Inba

Please use plain text.
Mentor
madhukeshwart
Posts: 273
Registered: ‎03-18-2009

Re: How to Activate 'Mold internal temperature result' in a 3D cool analysis?

06-06-2014 05:00 AM in reply to: mayur_dhumal

check the following

 

1) Create a mold boundary is must

2) In Advanced solver setting for cool.  select check box ' 'Calculate internal mold temperature' & set grid resolution value.

3) It is available for Cool ( BEM) method only, not for Cool (FEM)

4) Expected result is not available by default, you need to create custom plot.

 

If not solved your requirement . do let us know... 

Madhukeshwar Talwar
FIAT-CHRYSLER ATC, Chennai
mail: madhukeshwart@gmail.com
09600060862
======================================
Please use . Accept as Solution and Give Kudos as appropriate to further enhance these forums. Thank you! .....
Please use plain text.