Discussion Groups

Robot Structural Analysis

Reply
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012
Accepted Solution

RC BEAMS - SNIP - Area steel ?

533 Views, 9 Replies
12-21-2012 12:36 AM

Hi.. I is Prolem 

I use code Snip 2.

 

2012-02-18_1526.png

Please use plain text.
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012

Re: Area steel ?

12-21-2012 03:39 AM in reply to: A.wikipedia

Please. I is need. Thak

Please use plain text.
Product Support
Artur.Kosakowski
Posts: 4,836
Registered: ‎12-17-2010

Re: Area steel ?

12-21-2012 04:08 AM in reply to: A.wikipedia

Here you are.



Artur Kosakowski
Please use plain text.
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012

Re: Area steel ?

12-21-2012 05:45 AM in reply to: Artur.Kosakowski

Thanks. Athur

 

Please use plain text.
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012

Re: Area steel ?

12-24-2012 06:41 AM in reply to: A.wikipedia

Hi. I is prolem

Question 1. picture 1

Conver c of picture right ???

Question 2. Pticture 2

Why c=0????

I attment file picture under.

thanks

 

Please use plain text.
Product Support
Artur.Kosakowski
Posts: 4,836
Registered: ‎12-17-2010

Re: Area steel ?

12-27-2012 12:39 AM in reply to: A.wikipedia

Looking at the rtd file you sent the cover is displayed as 20 mm. Could you sen the rtd file where you have it displayed as 0 mm in the calculation note?



Artur Kosakowski
Please use plain text.
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012

Re: RC BEAMS - SNIP - Area steel ?

12-27-2012 02:53 AM in reply to: A.wikipedia

Is here.

Thanks. 

Please use plain text.
Product Support
Artur.Kosakowski
Posts: 4,836
Registered: ‎12-17-2010

Re: RC BEAMS - SNIP - Area steel ?

12-27-2012 03:19 AM in reply to: A.wikipedia

Thank you for the file. As far s I can see the 0 values are displayed when covers are locked. As you have the reinforcement frozen calculations of the beam will not change it therefore you can unmark these check boxes to have the correct value displayed in the calculation note.

 

cover2.PNG



Artur Kosakowski
Please use plain text.
Distinguished Contributor
A.wikipedia
Posts: 140
Registered: ‎08-03-2012

Re: RC BEAMS - SNIP - Area steel ?

12-27-2012 03:50 AM in reply to: Artur.Kosakowski

Thank Artur.

But If I not Fixed. As (robot) > As( hand).

2012-12-27_1846.png

Please use plain text.
Product Support
Artur.Kosakowski
Posts: 4,836
Registered: ‎12-17-2010

Re: RC BEAMS - SNIP - Area steel ?

12-27-2012 03:57 AM in reply to: A.wikipedia

1. Calculate beam with the fixed covers

2. Edit the value of covers in the calculation note or

2a. Freeze the reinforcement generated for the fixed covers

2b. Calculate the beam with frozen reinforcement again to have the 20 mm cover displayed in the note.

 



Artur Kosakowski
Please use plain text.