Revit MEP

Reply
Active Contributor
sforsberg215
Posts: 36
Registered: ‎02-23-2011
Message 1 of 5 (213 Views)

Setting up correct views for plumbing

213 Views, 4 Replies
11-26-2012 06:18 AM

Hello, Everyone!

 

I have a plumbing floor plan set up into 2 views, one for area "A" and one for area "B". Areas "A" and "B" are placed on their own sheet. The Problem: When I shut off revision clouds in area "A", the clouds in area "B" also shut off in spite of revison clouds and tags set to "by sheet".

 

I am pretty sure this is caused by using the wrong type of view. So, what kind of view should one use to set up so they act indepently of each other on the sheets?

 

There could be other setting problems I haven't thought of either, so I welcome any suggestions.

 

Thanks

Scott F

*Expert Elite*
CADastrophe
Posts: 3,334
Registered: ‎08-28-2009
Message 2 of 5 (201 Views)

Re: Setting up correct views for plumbing

11-26-2012 08:42 AM in reply to: sforsberg215

Are your areas Dependent Views? If this is the case, then changing the V/G Overrides on any of the Views will also change it in all of the other related Views, both master and dependent. You would have to either make the view Independent or hide the Revision Clouds by Element.

Corey D.                                                                                                                  ADSK_Logo_EE_2013.png    AutoCAD 2014 User  Revit 2014 User
──────────────────────────────────────────────────────────────────────
⁞|⁞ Please use Mark Solutions!.Accept as Solution and Give Kudos!Give Kudos as appropriate to further enhance these forums. Thank you!
Active Contributor
sforsberg215
Posts: 36
Registered: ‎02-23-2011
Message 3 of 5 (199 Views)

Re: Setting up correct views for plumbing

11-26-2012 09:12 AM in reply to: sforsberg215

Thanks.  

 

So, should Revision Clouds and Tags only be placed/ made on the Sheet, not the view?

*Expert Elite*
CADastrophe
Posts: 3,334
Registered: ‎08-28-2009
Message 4 of 5 (195 Views)

Re: Setting up correct views for plumbing

11-26-2012 09:47 AM in reply to: sforsberg215

I think that the Revision Clouds are best placed on the Sheet View, for reasons such as avoiding having to deal with annotation cropping and a more easily controlled appearance of the Revisions Clouds. This can be a debatable issue, though.

Corey D.                                                                                                                  ADSK_Logo_EE_2013.png    AutoCAD 2014 User  Revit 2014 User
──────────────────────────────────────────────────────────────────────
⁞|⁞ Please use Mark Solutions!.Accept as Solution and Give Kudos!Give Kudos as appropriate to further enhance these forums. Thank you!
Mentor
mike
Posts: 246
Registered: ‎03-04-2004
Message 5 of 5 (187 Views)

Re: Setting up correct views for plumbing

11-26-2012 10:51 AM in reply to: sforsberg215

Yes...On the sheet itself...not IN the particular view

 

Mike.

Michael L. Maloney
Virtual World Designs
VDC & BIM Model Design, Clash & Coordination
mike@VirtualWorldDesigns.com
Building Design Suite Ultimate 2013, 2014, 2015
Charlotte, NC ; Fort Mill, SC
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.