Revit MEP

Reply
Active Member
gyulas
Posts: 8
Registered: ‎08-31-2012
Message 1 of 7 (1,274 Views)
Accepted Solution

rectangular duct elbow fitting

1274 Views, 6 Replies
08-31-2012 07:30 AM

Hi all!

I have an issue while i use rectangular radius elbow in revit MEP 2012.

If the width and the height of duct is equal, it works properly, i can turn up and down with my duct.


But if the dimensions are different, it won't make any connections in vertical direction, and i get an error message (see attached).

I can rotate my elbow to the right direction, but i cannot make connection to my riser duct.

 

Any advice would be life saver,

Thank for help,

 

Gyula

This is possible. In the first example that your images depict, Revit might be looking for a Transition. Load in and define a default fitting for Tee, Transition, and Union to see if that affects the situation.

*Expert Elite*
CADastrophe
Posts: 3,402
Registered: ‎08-28-2009
Message 2 of 7 (1,186 Views)

Re: rectangular duct elbow fitting

09-04-2012 06:03 AM in reply to: gyulas

Are you drawing the horizontal and vertical duct and then trying to add the elbow between? You will find better success if you draw the duct run in a section view, so that the elbow is placed automatically.

 

⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗
Welcome to the Autodesk forums, gyulas!
Feel free to post any questions you may have! There are many experienced users here who generously contribute their time and effort to supporting
their peers. This is an open, peer-supported forum, so feel free to contribute any useful information or experiences to any of the topics you see here.
We hope you'll stick around a while and help strengthen the value of this community!
───────────────────────────────────────────────────────────────────────────────────────────
Be sure to review the Ground Rules, visit the FAQ Forum, and use the Search feature prior to posting a question, as it's likely been asked before.
⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗⸗

Corey D.                                                                                                                  ADSK_Logo_EE_2013.png    AutoCAD 2014 User  Revit 2014 User
──────────────────────────────────────────────────────────────────────
⁞|⁞ Please use Mark Solutions!.Accept as Solution and Give Kudos!Give Kudos as appropriate to further enhance these forums. Thank you!
Active Member
gyulas
Posts: 8
Registered: ‎08-31-2012
Message 3 of 7 (1,183 Views)

Re: rectangular duct elbow fitting

09-04-2012 06:24 AM in reply to: CADastrophe

First i drew the horizontal part of my duct. After i added the elevation where i would like to arrive. It did not work.

I have tried it in section view, but the solution was the same.

 

Elbow fitting was from the revit library, and we have started to work in an empty project file (imperial).

*Expert Elite*
CADastrophe
Posts: 3,402
Registered: ‎08-28-2009
Message 4 of 7 (1,179 Views)

Re: rectangular duct elbow fitting

09-04-2012 06:29 AM in reply to: gyulas

Does the Duct Type have a default elbow defined? If you just draw some Duct in an "L" shape (within the same command, two clicks), does it automatically create the elbow? Depending on the template the project was started with, the Duct Type Properties might have to be modified.

Corey D.                                                                                                                  ADSK_Logo_EE_2013.png    AutoCAD 2014 User  Revit 2014 User
──────────────────────────────────────────────────────────────────────
⁞|⁞ Please use Mark Solutions!.Accept as Solution and Give Kudos!Give Kudos as appropriate to further enhance these forums. Thank you!
Active Member
gyulas
Posts: 8
Registered: ‎08-31-2012
Message 5 of 7 (1,176 Views)

Re: rectangular duct elbow fitting

09-04-2012 06:54 AM in reply to: CADastrophe

I defined the elbow type, it works well if i draw it horizontally.

 

But, i think i haven't set any project template before i start.

 

I have only defined the elbow fitting type. Could it be the reason of this issue that i haven't defined the other fiting types?

*Expert Elite*
CADastrophe
Posts: 3,402
Registered: ‎08-28-2009
Message 6 of 7 (1,170 Views)

Re: rectangular duct elbow fitting

09-04-2012 07:03 AM in reply to: gyulas

This is possible. In the first example that your images depict, Revit might be looking for a Transition. Load in and define a default fitting for Tee, Transition, and Union to see if that affects the situation.

Corey D.                                                                                                                  ADSK_Logo_EE_2013.png    AutoCAD 2014 User  Revit 2014 User
──────────────────────────────────────────────────────────────────────
⁞|⁞ Please use Mark Solutions!.Accept as Solution and Give Kudos!Give Kudos as appropriate to further enhance these forums. Thank you!
Active Member
gyulas
Posts: 8
Registered: ‎08-31-2012
Message 7 of 7 (1,167 Views)

Re: rectangular duct elbow fitting

09-04-2012 07:08 AM in reply to: CADastrophe

It works well in this way. :smileyhappy:

 

Thanks for your help.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!