Revit MEP Wishes

Reply
Member
ptbreisch
Posts: 4
Registered: ‎11-13-2006
Message 1 of 8 (446 Views)

homerun arrows

446 Views, 7 Replies
07-30-2008 02:51 PM
i would like to see the flexibility of turning off homerun arrows in a circuit run that when creating a circuit of a number of devices they dont show up until you get to the homerun itself. or give us the flexiblity to size and move the homeruns along a circuit so that they dont look a bit "special" when it bumps a device
Active Member
RedCarsRule
Posts: 10
Registered: ‎01-29-2003
Message 2 of 8 (446 Views)

Re: homerun arrows

07-30-2009 04:05 PM in reply to: ptbreisch
Absolutely necessary, the arrowheads showing up on downstream device circuits obliterate the device they are connected to.
Distinguished Contributor
sschwartz
Posts: 540
Registered: ‎09-16-2005
Message 3 of 8 (446 Views)

Re: homerun arrows

09-30-2009 08:17 AM in reply to: ptbreisch
Got my vote!!!!!!

Is it really a "home run" from one light fixture to the next? (I don't think so!)
New Member
tgferguson
Posts: 1
Registered: ‎07-11-2012
Message 4 of 8 (380 Views)

Re: homerun arrows

07-11-2012 11:15 AM in reply to: ptbreisch

It is very odd that by this time with so many engineers having the same concern that a fix has not been created.  There is no designer anywhere that would consider this graphic flaw in circuiting acceptable.  Please Autodesk if you have any concern on the correct graphic output of the Revit Electrical system fix this as soon as possible.

New Member
madpal11
Posts: 2
Registered: ‎04-22-2013
Message 5 of 8 (305 Views)

Re: homerun arrows

04-22-2013 02:26 PM in reply to: ptbreisch

I may be new to Revit MEP but the inital post was on: 07-30-2008 02:51 PM. The last post on this discussion group was on 07-11-2012 11:15 AM.

 

Out of sheer curiosity, does Autodesk - who as an unbelievable source of manpower - cannot (for the life of me) resolve this or be willing to even listen to this minimal request after 4+ years?

 

Is it maybe because only four interested, 5 now including me, have made comments? Makes me wonder how much more till a wish is finally granted...

 

By the way, been trying to figure this out and still to no avail on MEP 2013 - the arrows just doesn't look graphically right, yet it seems that Autodesk thinks its fine when it comes to circuiting! Quite ironic in a sense.

 

Here's to hoping :smileyindifferent:

New Member
madpal11
Posts: 2
Registered: ‎04-22-2013
Message 6 of 8 (301 Views)

Re: homerun arrows

04-22-2013 02:38 PM in reply to: madpal11
even if we can turn it off on vv/vg settings it still doesn't work the way one would like it shown. more control would be better for sure.
Active Member
shawnh
Posts: 7
Registered: ‎04-12-2013
Message 7 of 8 (290 Views)

Re: homerun arrows

04-26-2013 04:03 PM in reply to: ptbreisch

This absolutly needs to be fixed.  Working in the design build field with contractors, it gets brought up over and over again about how the homeruns look <insert word here>! Also, the multiple arrows at the end of the run in not necessary either, please make this a non-defaut option rather than the only option.

Valued Mentor
smbrennan85
Posts: 281
Registered: ‎09-29-2010
Message 8 of 8 (257 Views)

Re: homerun arrows

06-18-2013 01:01 PM in reply to: shawnh

It is very very sad that after 5 years, not we're still asking for HOME RUN ARROWS. Come on Autodesk, listen to the cries of the electrical industry. We're feeling negelected here!!!

Shawn B.

Follow me on Twitter @That85CADGuy.  ||    Connect with me on Linkedin.
To help improve Autodesk Products, please Click Here to provide feedback.
To help improve the use of these Forums, please  Accept As Solution and  Give Kudos.

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.