Revit Architecture

Reply
Valued Mentor
ennujozlagam
Posts: 435
Registered: ‎10-08-2007
Message 1 of 7 (450 Views)
Accepted Solution

Vanity Top Materials

450 Views, 6 Replies
08-01-2011 02:14 AM

Hi Guys,

 

Maybe you could help with this. I tried to create a vanity top ( for my toilet) using  Model in place - Sweep profiles and assigned materials finished but it didnt showed up. is this can be done? or is there any easiest way to do a vanity top and can apply materials? Please find enclosed.

 

Thank you,

one more step.

 

see attached.

Mentor
cbcarch
Posts: 214
Registered: ‎10-29-2008
Message 2 of 7 (414 Views)

Re: Vanity Top Materials

08-02-2011 07:46 AM in reply to: ennujozlagam

Instead of modeling it in-place:

 

Use a Casework --Countertop Family for this. There should be one that comes with Revit out of the box, with parameters

for length, width, height, counte thickness, and Materials.

 

Load it into your project and then specify the Materials. You should even be able to assign separate Materials for the countertop and the backsplash, if needed.

 

cheers

Cliff B. Collins
Registered Architect/BIM Specialist
Autodesk Revit Expert Elite
Valued Mentor
ennujozlagam
Posts: 435
Registered: ‎10-08-2007
Message 3 of 7 (384 Views)

Re: Vanity Top Materials

08-03-2011 05:40 PM in reply to: cbcarch

Hi,

 

I tried to look for this casework-counter top family but i cant find it. Do you know where it is?

 

Thanks,

*Expert Elite*
ccollins
Posts: 866
Registered: ‎09-28-2009
Message 4 of 7 (378 Views)

Re: Vanity Top Materials

08-04-2011 05:39 AM in reply to: ennujozlagam

see attached.

 

cheers

Cliff B. Collins
Registered Architect/BIM Manager
Thalden Boyd Emery Architects
St. Louis, MO
*Expert Elite*
ccollins
Posts: 866
Registered: ‎09-28-2009
Message 5 of 7 (372 Views)

Re: Vanity Top Materials

08-04-2011 08:48 AM in reply to: ccollins

one more step.

 

see attached.

Cliff B. Collins
Registered Architect/BIM Manager
Thalden Boyd Emery Architects
St. Louis, MO
Valued Mentor
ennujozlagam
Posts: 435
Registered: ‎10-08-2007
Message 6 of 7 (357 Views)

Re: Vanity Top Materials

08-04-2011 05:27 PM in reply to: ccollins

Hi Cliff,

 

Thank you very much for your help. Appreciated. Can i ask you again. I have to draw in Revit Steel staircase which means all the riser, steps and even landing are in steel profile, But i really dont know how and where to start? maybe if you could help with this?

 

Thank you and God Bless..

*Expert Elite*
ccollins
Posts: 866
Registered: ‎09-28-2009
Message 7 of 7 (346 Views)

Re: Vanity Top Materials

08-05-2011 06:09 AM in reply to: ennujozlagam

Glad it worked.

 

For the steel stairs, try using Help in Revit for creating stairs--this should be a good place to begin.

 

If you then have trouble or more detailed questions, start a new thread on the forum.

 

Hint: Revit will create your stairs and railings automatically. You select the stair tool, draw the run(s) in plan,

specify which Levels the stair begins and ends at, click finish and it is done. That said, there are some problems

with the stair and railing tools, most of which can be overcome with tricky workarounds. But if it is a basic stair,

you should be able to create it quickly and effectively.

 

cheers

Cliff B. Collins
Registered Architect/BIM Manager
Thalden Boyd Emery Architects
St. Louis, MO
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.