Revit Architecture

Revit Architecture

Reply
Valued Contributor
gdfisher
Posts: 77
Registered: ‎11-11-2010
Message 1 of 6 (7,527 Views)

Brick Soldier Course over arch-top french door in stone wall

7527 Views, 5 Replies
09-15-2011 09:08 AM

Has anyone found a successful method to add a brick soldier course over an arch-top door in a stone wall? I'd like the brick type and quantity to show up in the materials list. I'm a student using a complimentary copy of Revit Architecture 2011.

*Expert Elite*
rosskirby
Posts: 886
Registered: ‎04-08-2008
Message 2 of 6 (7,524 Views)

Re: Brick Soldier Course over arch-top french door in stone wall

09-15-2011 09:20 AM in reply to: gdfisher

Quantity of brick in an arch seems like overkill to me, but to each his own.

 

Make a generic model of a brick, load it into your door family, place it, constrain it, array it as required.  Set up parameters to control the spacing, array distance and radius, and tie them to the size and radius of your door.

Ross Kirby
BIM Manager
Arcturis
Valued Contributor
gdfisher
Posts: 77
Registered: ‎11-11-2010
Message 3 of 6 (7,494 Views)

Re: Brick Soldier Course over arch-top french door in stone wall

09-16-2011 01:14 PM in reply to: rosskirby

Thanks for taking the time to post your suggestion. Re. Soldier course quantity, project ios a large residence with every wall penetration framed with brick - top, sides and bottom - not an inconsequential amount for costing. Thanks again.

*Expert Elite*
rosskirby
Posts: 886
Registered: ‎04-08-2008
Message 4 of 6 (7,489 Views)

Re: Brick Soldier Course over arch-top french door in stone wall

09-16-2011 01:21 PM in reply to: gdfisher

I was assuming that the rest of the building was brick as well, in which case the number of bricks in an arch is relatively inconsequential.  I would suggest using a solid extrusion to represent the shape of the arch, use an array of model lines to represent the mortar joints, and apply a material placeholder in the family.  Then, in the project, assign that arch the same material as you use for the rest of the brick, then do a simple quantity takeoff schedule.

Ross Kirby
BIM Manager
Arcturis
*Expert Elite*
ccollins
Posts: 866
Registered: ‎09-28-2009
Message 5 of 6 (7,488 Views)

Re: Brick Soldier Course over arch-top french door in stone wall

09-16-2011 01:22 PM in reply to: gdfisher

You could use a formula and a calculated value to figure out how many bricks are in the soldier courses if necessary.

 

In theory,

If you wanted to take it quite literally, you could model an actual brick, create a radial array, then Group it.

Give the Bricks a special unique Material--such as Brick-Soldier

Copy the Group around as required. Then generate a Material Takeoff, and it will quantify how many bricks you have.

Or perhaps at least how many SQ FT of the material you have, then use a formula to dtermine how many bricks.

 

cheers

Cliff B. Collins
Registered Architect/BIM Manager
Thalden Boyd Emery Architects
St. Louis, MO
Contributor
Greenhatchgroup
Posts: 12
Registered: ‎07-24-2013
Message 6 of 6 (4,907 Views)

Re: Brick Soldier Course over arch-top french door in stone wall

01-22-2014 03:43 AM in reply to: gdfisher

Try the family on this site http://essentialbim.com/product/brick-arch/,

 

We purchased it and it worked great, I spent ages trying to figure out how to get the bricks to nest properly and work, yet failed everytime, in the end the £3 I spent on this family was well worth it and saved me a lot more effort.

 

Basically it does as suggested above, an array of bricks around an arch, there arre lots of good calculations to allow you to flex the overall width, arch height and number of bricks, just share the parameters for takeoffs etc.

 

Hope this helps

 

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.