Inventor Publisher

Inventor Publisher

Reply
*Expert Elite*
Mark_Flayler
Posts: 1,477
Registered: ‎07-30-2007
Message 1 of 7 (362 Views)

Inventor Publisher 2013; Cannot Load any New Files

362 Views, 6 Replies
05-04-2012 11:30 AM

I am able to open existing .ipb files and work with them normally, however, whenever I try to bring in an Inventor assembly or part, I get a hang up and eventual crash.

 

I have Inventor 2012 and 2013 installed and this happens with either format used in Inventor Publisher 2013.

 

I have Serice Pack 1 installed as well as when I installed the software I had UAC turned off.  I have run an Reinstall through the Control Panel and this has not solved the issue either.  How am I supposed to use this if I can't get an Inventor file into the storyboard?!?!?

Mark Flayler - Senior Application Engineer
IMAGINiT's Manufacturing Solutions Blog:
http://blogs.rand.com/manufacturing/
Employee
kumarra
Posts: 78
Registered: ‎10-15-2008
Message 2 of 7 (361 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-04-2012 11:34 AM in reply to: Mark_Flayler

Hello Mark,

 

Are you experiencing this issue after you updated to Service pack 1?

 

 

Thanks,
Rajkumar
*Expert Elite*
Mark_Flayler
Posts: 1,477
Registered: ‎07-30-2007
Message 3 of 7 (359 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-04-2012 11:36 AM in reply to: Mark_Flayler

Yes.

Mark Flayler - Senior Application Engineer
IMAGINiT's Manufacturing Solutions Blog:
http://blogs.rand.com/manufacturing/
Employee
kumarra
Posts: 78
Registered: ‎10-15-2008
Message 4 of 7 (353 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-04-2012 01:34 PM in reply to: Mark_Flayler

Mark,

 

I tried importing a few Inventor assembly files and did not have any issues. Would it be possible to pack and go a small file that you are having this issue and email it to rajkumar.ilannchelian@autodesk.com? If the file size is larger than 10MB please email me and I will send you a dropbox share to upload the file.

 

 

Thanks,
Rajkumar
*Expert Elite*
Mark_Flayler
Posts: 1,477
Registered: ‎07-30-2007
Message 5 of 7 (351 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-04-2012 01:44 PM in reply to: Mark_Flayler

To be honest, its not a file issue, it happens on all files no matter their creation.  I did find a workaround in that if I already have an IPB open and then start a new document I am able to import, I just can't do it from scratch without already haveing something open.  This seems like a bug to me or a bad installer.  I sincerely doubt you can help me with getting a file set (it even happens on the Publisher sample data sets and courseware files).

 

About the only way you could assist at this point may be a remote desktop and inspect the issue and perhaps the installer files.

Mark Flayler - Senior Application Engineer
IMAGINiT's Manufacturing Solutions Blog:
http://blogs.rand.com/manufacturing/
*Expert Elite*
Mark_Flayler
Posts: 1,477
Registered: ‎07-30-2007
Message 6 of 7 (343 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-06-2012 10:24 AM in reply to: Mark_Flayler

Driver Issue.  Installed new Video driver for my Quadro FX880 and it works fine now.

 

Thank you for your help though.

Mark Flayler - Senior Application Engineer
IMAGINiT's Manufacturing Solutions Blog:
http://blogs.rand.com/manufacturing/
Employee
kumarra
Posts: 78
Registered: ‎10-15-2008
Message 7 of 7 (334 Views)

Re: Inventor Publisher 2013; Cannot Load any New Files

05-07-2012 07:48 AM in reply to: Mark_Flayler

Thanks for the update. Glad to hear that it is a non-issue.

Thanks,
Rajkumar
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!