Inventor General Discussion

Reply
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 1 of 16 (366 Views)

Will my model break

366 Views, 15 Replies
11-12-2012 03:58 PM

I've created a model in inventor that is a plate with two pins coming off of it. (Made from ABS)

 

what i was wondering was weather there was a way to test wether the pin would snap when a force is aplied to it? I'm also interested in how much it will flex But it isn't essential.

 

how can I do this in inventor?? 

 

 

Thanks Ed. :smileyhappy:

*Expert Elite*
Cadmanto
Posts: 3,264
Registered: ‎12-07-2011
Message 2 of 16 (355 Views)

Re: Will my model break

11-12-2012 05:32 PM in reply to: EdwardCChamberlain

Ed,

You would have to do a stress analysis in Inventor.

What version of Inventor do you have?

 

Best Regards,
Scott McFadden
Inventor Professional 2013
(Colossians 3:23-25)

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 3 of 16 (309 Views)

Re: Will my model break

11-13-2012 09:40 AM in reply to: Cadmanto

im using 2013, will have a look at that link. so far ive only managed to make it bend the part? :smileyfrustrated: 

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 4 of 16 (305 Views)

Re: Will my model break

11-13-2012 09:55 AM in reply to: Cadmanto

so as i understand if i see red anywhere in my simulation: It will break? 

 

Thanks

Ed.

*Expert Elite*
JDMather
Posts: 26,821
Registered: ‎04-20-2006
Message 5 of 16 (304 Views)

Re: Will my model break

11-13-2012 09:55 AM in reply to: EdwardCChamberlain

Attach your file here.

Inventor does not do fracture analysis.

It will show you where part goes beyond elastic deformation into plastic deformation.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 6 of 16 (296 Views)

Re: Will my model break

11-13-2012 10:16 AM in reply to: JDMather

Regretably i cant attach the actual design file but i will attach a demonstration piece when i get back to my computer.

 

So the plastic deformantion is a permenant change? Whereas elastic deformation is reversable? If so then i would require no plastic deformation. 

 

Thanks Ed. 

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 7 of 16 (256 Views)

Re: Will my model break

11-13-2012 01:51 PM in reply to: EdwardCChamberlain

Ive attached a model. I want to apply pressure along the x and z axis to the top of the thinner rod. And then id want to know wether that rod would snap off. 

 

Thanks Ed.

*Expert Elite*
JDMather
Posts: 26,821
Registered: ‎04-20-2006
Message 8 of 16 (253 Views)

Re: Will my model break

11-13-2012 01:57 PM in reply to: EdwardCChamberlain

There is no material assigned.

Inventor doesn't do fracture analysis.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 9 of 16 (236 Views)

Re: Will my model break

11-13-2012 03:18 PM in reply to: JDMather

it should be assigned ABS plastic, and ok is there a way of finding out wether it will be irreverably dammaged? 

*Expert Elite*
JDMather
Posts: 26,821
Registered: ‎04-20-2006
Message 10 of 16 (229 Views)

Re: Will my model break

11-13-2012 04:07 PM in reply to: EdwardCChamberlain

EdwardCChamberlain wrote:

Ive attached a model. I want to apply pressure along the x and z axis to the top of the thinner rod.

Thanks Ed.


 Along the x and z where?  Equal in each direction?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.