Inventor General Discussion

Inventor General Discussion

Reply
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 1 of 16 (393 Views)

Will my model break

393 Views, 15 Replies
11-12-2012 03:58 PM

I've created a model in inventor that is a plate with two pins coming off of it. (Made from ABS)

 

what i was wondering was weather there was a way to test wether the pin would snap when a force is aplied to it? I'm also interested in how much it will flex But it isn't essential.

 

how can I do this in inventor?? 

 

 

Thanks Ed. :smileyhappy:

*Expert Elite*
Cadmanto
Posts: 3,356
Registered: ‎12-07-2011
Message 2 of 16 (382 Views)

Re: Will my model break

11-12-2012 05:32 PM in reply to: EdwardCChamberlain

Ed,

You would have to do a stress analysis in Inventor.

What version of Inventor do you have?

 

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 3 of 16 (336 Views)

Re: Will my model break

11-13-2012 09:40 AM in reply to: Cadmanto

im using 2013, will have a look at that link. so far ive only managed to make it bend the part? :smileyfrustrated: 

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 4 of 16 (332 Views)

Re: Will my model break

11-13-2012 09:55 AM in reply to: Cadmanto

so as i understand if i see red anywhere in my simulation: It will break? 

 

Thanks

Ed.

*Expert Elite*
JDMather
Posts: 28,255
Registered: ‎04-20-2006
Message 5 of 16 (331 Views)

Re: Will my model break

11-13-2012 09:55 AM in reply to: EdwardCChamberlain

Attach your file here.

Inventor does not do fracture analysis.

It will show you where part goes beyond elastic deformation into plastic deformation.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 6 of 16 (323 Views)

Re: Will my model break

11-13-2012 10:16 AM in reply to: JDMather

Regretably i cant attach the actual design file but i will attach a demonstration piece when i get back to my computer.

 

So the plastic deformantion is a permenant change? Whereas elastic deformation is reversable? If so then i would require no plastic deformation. 

 

Thanks Ed. 

Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 7 of 16 (283 Views)

Re: Will my model break

11-13-2012 01:51 PM in reply to: EdwardCChamberlain

Ive attached a model. I want to apply pressure along the x and z axis to the top of the thinner rod. And then id want to know wether that rod would snap off. 

 

Thanks Ed.

*Expert Elite*
JDMather
Posts: 28,255
Registered: ‎04-20-2006
Message 8 of 16 (280 Views)

Re: Will my model break

11-13-2012 01:57 PM in reply to: EdwardCChamberlain

There is no material assigned.

Inventor doesn't do fracture analysis.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
EdwardCChamberlain
Posts: 16
Registered: ‎11-05-2012
Message 9 of 16 (263 Views)

Re: Will my model break

11-13-2012 03:18 PM in reply to: JDMather

it should be assigned ABS plastic, and ok is there a way of finding out wether it will be irreverably dammaged? 

*Expert Elite*
JDMather
Posts: 28,255
Registered: ‎04-20-2006
Message 10 of 16 (256 Views)

Re: Will my model break

11-13-2012 04:07 PM in reply to: EdwardCChamberlain

EdwardCChamberlain wrote:

Ive attached a model. I want to apply pressure along the x and z axis to the top of the thinner rod.

Thanks Ed.


 Along the x and z where?  Equal in each direction?

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.