Inventor General Discussion

Reply
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 1 of 13 (512 Views)

Weldment

512 Views, 12 Replies
10-26-2010 04:48 AM

The file attached contains a main pipe with 4 flanges mated onto the pipe.I have not used the Weldment feature before so would please like some guideance and help.What steps would i use to Weld the 2 small upright pipes on top of the main pipe and Weld the 4 flanges onto the 4 small curved pipes underneath the main pipe?

Any help appreciated.....IJC

*Expert Elite*
blair
Posts: 4,217
Registered: ‎11-13-2006
Message 2 of 13 (490 Views)

Re: Weldment

10-26-2010 04:11 PM in reply to: ijc

First, you need to either convert this existing model to a Weldment, or start a new model as a weldment. Then enter the Weld Module. The rest is straight forward, or read the "Help"

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 3 of 13 (484 Views)

Re: Weldment

10-26-2010 04:26 PM in reply to: blair

Blair...thanks for the reply....will take your advice and follow.

 

Blair is also possible to use Weld where i attached the 4 flanges onto the curved pipes under the main pipe?

 

Best Regards

 

IJC

*Expert Elite*
blair
Posts: 4,217
Registered: ‎11-13-2006
Message 4 of 13 (479 Views)

Re: Weldment

10-26-2010 04:29 PM in reply to: ijc

Yes, it's done the same way.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 5 of 13 (477 Views)

Re: Weldment

10-26-2010 04:30 PM in reply to: ijc

Thank you

Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 6 of 13 (443 Views)

Re: Weldment

10-27-2010 05:29 AM in reply to: ijc

I was able to weld the 2 end pipes but was not able to weld the middle pipe.I used the same technique as the 2 end pipes but could not get it to work.I also tried some other welds but again would not work...What technique is required to weld the middle pipe onto the bottom pipe?

Thanks....IJC

*Expert Elite*
blair
Posts: 4,217
Registered: ‎11-13-2006
Message 7 of 13 (420 Views)

Re: Weldment

10-27-2010 08:39 AM in reply to: ijc

Your IAM file is useless without the required IPTfiles

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 8 of 13 (402 Views)

Re: Weldment

10-27-2010 04:31 PM in reply to: blair

Here is the file..thanks

*Expert Elite*
blair
Posts: 4,217
Registered: ‎11-13-2006
Message 9 of 13 (397 Views)

Re: Weldment

10-27-2010 04:51 PM in reply to: ijc

The files you sent only contain a single part "Part1" and it's a flat plate with a slot and a couple of other holes.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 150
Registered: ‎07-03-2010
Message 10 of 13 (393 Views)

Re: Weldment

10-27-2010 05:08 PM in reply to: blair

 

Will this picture help..The large pipe in the middle without the weld is the one i cannot get to work... Both pipes are 3" in diameter...thanks again

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.