Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 1 of 13 (520 Views)

Weldment

520 Views, 12 Replies
10-26-2010 04:48 AM

The file attached contains a main pipe with 4 flanges mated onto the pipe.I have not used the Weldment feature before so would please like some guideance and help.What steps would i use to Weld the 2 small upright pipes on top of the main pipe and Weld the 4 flanges onto the 4 small curved pipes underneath the main pipe?

Any help appreciated.....IJC

*Expert Elite*
blair
Posts: 4,443
Registered: ‎11-13-2006
Message 2 of 13 (498 Views)

Re: Weldment

10-26-2010 04:11 PM in reply to: ijc

First, you need to either convert this existing model to a Weldment, or start a new model as a weldment. Then enter the Weld Module. The rest is straight forward, or read the "Help"

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 3 of 13 (492 Views)

Re: Weldment

10-26-2010 04:26 PM in reply to: blair

Blair...thanks for the reply....will take your advice and follow.

 

Blair is also possible to use Weld where i attached the 4 flanges onto the curved pipes under the main pipe?

 

Best Regards

 

IJC

*Expert Elite*
blair
Posts: 4,443
Registered: ‎11-13-2006
Message 4 of 13 (487 Views)

Re: Weldment

10-26-2010 04:29 PM in reply to: ijc

Yes, it's done the same way.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 5 of 13 (485 Views)

Re: Weldment

10-26-2010 04:30 PM in reply to: ijc

Thank you

Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 6 of 13 (451 Views)

Re: Weldment

10-27-2010 05:29 AM in reply to: ijc

I was able to weld the 2 end pipes but was not able to weld the middle pipe.I used the same technique as the 2 end pipes but could not get it to work.I also tried some other welds but again would not work...What technique is required to weld the middle pipe onto the bottom pipe?

Thanks....IJC

*Expert Elite*
blair
Posts: 4,443
Registered: ‎11-13-2006
Message 7 of 13 (428 Views)

Re: Weldment

10-27-2010 08:39 AM in reply to: ijc

Your IAM file is useless without the required IPTfiles

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 8 of 13 (410 Views)

Re: Weldment

10-27-2010 04:31 PM in reply to: blair

Here is the file..thanks

*Expert Elite*
blair
Posts: 4,443
Registered: ‎11-13-2006
Message 9 of 13 (405 Views)

Re: Weldment

10-27-2010 04:51 PM in reply to: ijc

The files you sent only contain a single part "Part1" and it's a flat plate with a slot and a couple of other holes.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 344.75
SpacePilot Pro 10.2.0 / 17.2.0.11011 / 4.17
Delta Tau Chi ΔΤΧ
Distinguished Contributor ijc
Distinguished Contributor
ijc
Posts: 155
Registered: ‎07-03-2010
Message 10 of 13 (401 Views)

Re: Weldment

10-27-2010 05:08 PM in reply to: blair

 

Will this picture help..The large pipe in the middle without the weld is the one i cannot get to work... Both pipes are 3" in diameter...thanks again

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.