Inventor General Discussion

Inventor General Discussion

Reply
*Sofia Grave
Message 1 of 17 (382 Views)

Subtract part

382 Views, 16 Replies
10-22-2009 04:13 AM
Hej to all

I need a big help, I have a part, but i need now is the negative of that
part.
This part have a few channels inside and I need the volume of the channels,
in other words, i need to have in 3d the channels and all the other paths. I
need the empty shapes in my part to became a solid.
How can i do this?

Thanks to all.
sofia
*Expert Elite*
JDMather
Posts: 28,254
Registered: ‎04-20-2006
Message 2 of 17 (382 Views)

Re: Subtract part

10-22-2009 04:17 AM in reply to: *Sofia Grave
You didn't state what version of Inventor you are using.
You didn't post example file here.

2010 Combine with cut

earlier - Derived Component with Split or Sculpt.
Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
*Sofia Grave
Message 3 of 17 (382 Views)

Re: Subtract part

10-22-2009 04:30 AM in reply to: *Sofia Grave
Sorry

I am using IV2010.
I am attachging the file, I need all the inner channels as solids. like the
negative,
than ks

"JDMather" wrote in message news:6275993@discussion.autodesk.com...
> You didn't state what version of Inventor you are using.
> You didn't post example file here.
>
> 2010 Combine with cut
>
> earlier - Derived Component with Split or Sculpt.
Distinguished Contributor
HallStevenson
Posts: 216
Registered: ‎09-29-2008
Message 4 of 17 (382 Views)

Re: Subtract part

10-22-2009 05:29 AM in reply to: *Sofia Grave
> {quote:title=JDMather wrote:}{quote}
> You didn't post example file here.

JD, her sketches are constrained :-)
*Dennis Jeffrey
Message 5 of 17 (382 Views)

Re: Subtract part

10-22-2009 05:40 AM in reply to: *Sofia Grave
Results of 2010:

1. Extrude a new body over the entire part.
2. Using the new Solid 2 as the Base, Combine - intersect using the
original Solid 1 as the Toolbody.

Result is as shown.

3. Use Delete Face (Lump) to remove any unwanted geometry.
--
Dennis Jeffrey, Autodesk Inventor Certified Expert
Autodesk Manufacturing Implementation Certified Expert.
Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
http://teknigroup.com
*Sofia Grave
Message 6 of 17 (382 Views)

Re: Subtract part

10-22-2009 06:29 AM in reply to: *Sofia Grave
Wonderful answer, but now cames the next question, how did you made the
solid over the 1 solid?
but that is exactly what I want.

"Dennis Jeffrey" wrote in message
news:6276057@discussion.autodesk.com...
> Results of 2010:
>
> 1. Extrude a new body over the entire part.
> 2. Using the new Solid 2 as the Base, Combine - intersect using the
> original Solid 1 as the Toolbody.
>
> Result is as shown.
>
> 3. Use Delete Face (Lump) to remove any unwanted geometry.
> --
> Dennis Jeffrey, Autodesk Inventor Certified Expert
> Autodesk Manufacturing Implementation Certified Expert.
> Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
> http://teknigroup.com
>
*Dennis Jeffrey
Message 7 of 17 (382 Views)

Re: Subtract part

10-22-2009 06:30 AM in reply to: *Sofia Grave
Here's the part.
--
Dennis Jeffrey, Autodesk Inventor Certified Expert
Autodesk Manufacturing Implementation Certified Expert.
Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
http://teknigroup.com
*Sofia Grave
Message 8 of 17 (382 Views)

Re: Subtract part

10-22-2009 06:47 AM in reply to: *Sofia Grave
Thnak you,
But I would love to know how you did that.

"Dennis Jeffrey" wrote in message
news:6276120@discussion.autodesk.com...
> Here's the part.
> --
> Dennis Jeffrey, Autodesk Inventor Certified Expert
> Autodesk Manufacturing Implementation Certified Expert.
> Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
> http://teknigroup.com
>
*Dennis Jeffrey
Message 9 of 17 (382 Views)

Re: Subtract part

10-22-2009 07:17 AM in reply to: *Sofia Grave
Sorry, meant CUT, not Intersect. I'll do a video for you...
--
Dennis Jeffrey, Autodesk Inventor Certified Expert
Autodesk Manufacturing Implementation Certified Expert.
Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
http://teknigroup.com
*Sofia Grave
Message 10 of 17 (382 Views)

Re: Subtract part

10-22-2009 07:33 AM in reply to: *Sofia Grave
Thank you thank you, that will be a huge help for the future.

"Dennis Jeffrey" wrote in message
news:6276157@discussion.autodesk.com...
> Sorry, meant CUT, not Intersect. I'll do a video for you...
> --
> Dennis Jeffrey, Autodesk Inventor Certified Expert
> Autodesk Manufacturing Implementation Certified Expert.
> Instructor/Author/Sr. App Engr. Tel. (260) 399-6615
> http://teknigroup.com
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.