Inventor General Discussion

Inventor General Discussion

Reply
Valued Contributor hlo
Valued Contributor
hlo
Posts: 91
Registered: ‎10-08-2006
Message 1 of 5 (396 Views)
Accepted Solution

Stress analysis - deflection of a steel block

396 Views, 4 Replies
11-19-2012 03:21 AM

HI

 

Is it possible to calculate the deflection a steel block will get, just form it one weight

Just use standard steel material, it is only supported at the end.

 

 

Regards

Henrik

Yes, it is possible. I assume you want to place the Weight positioned along the bar at a set distance.

You can do this by splitting the face with either a circle or rectangle and placing your force there.

I have attached an example. Hopefully I have understood your question.

Jon.

The Gravity Vector is just that, the direction/vector that gravity will affect the model in question. It doesn't matter which object/edge you select. If an edge is not in the correct direction, you can expand the box and enter a vector using the XZY boxes.

 

You need to create a sketch on the desired surface and then create a closed loop then exit the sketch. Select the Split Tool command, then the sketch (closed profile) and finally the surface in question.

 

If you wish to apply a load to a given spot/area on a surface, you would be required to use the Split Surface to create a separate surface in which to apply either the force/load or support constrain. Otherwise Inventor will apply the load/constrain to the whole surface face.

Product Support
jon.dean
Posts: 193
Registered: ‎06-02-2010
Message 2 of 5 (357 Views)

Re: Stress analysis - deflection of a steel block

11-23-2012 07:11 AM in reply to: hlo

Yes, it is possible. I assume you want to place the Weight positioned along the bar at a set distance.

You can do this by splitting the face with either a circle or rectangle and placing your force there.

I have attached an example. Hopefully I have understood your question.

Jon.



Jon Dean

*Expert Elite*
blair
Posts: 4,192
Registered: ‎11-13-2006
Message 3 of 5 (340 Views)

Re: Stress analysis - deflection of a steel block

11-23-2012 11:58 AM in reply to: jon.dean

Remember to add the directionof gravity to your analysis (if applicable).

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Valued Contributor hlo
Valued Contributor
hlo
Posts: 91
Registered: ‎10-08-2006
Message 4 of 5 (318 Views)

Re: Stress analysis - deflection of a steel block

11-25-2012 12:06 AM in reply to: blair

HI

 

Hi

Thank for reply, i do understand the estimated setup and way to get a bending result

The gravity vector where shout it be placed in this example

 

Another question regarding the use of split tool, what dose I do to the surface, is it only

marking a round spot and not removing  anything.

 

Regards

Henrik

*Expert Elite*
blair
Posts: 4,192
Registered: ‎11-13-2006
Message 5 of 5 (301 Views)

Re: Stress analysis - deflection of a steel block

11-25-2012 10:47 AM in reply to: hlo

The Gravity Vector is just that, the direction/vector that gravity will affect the model in question. It doesn't matter which object/edge you select. If an edge is not in the correct direction, you can expand the box and enter a vector using the XZY boxes.

 

You need to create a sketch on the desired surface and then create a closed loop then exit the sketch. Select the Split Tool command, then the sketch (closed profile) and finally the surface in question.

 

If you wish to apply a load to a given spot/area on a surface, you would be required to use the Split Surface to create a separate surface in which to apply either the force/load or support constrain. Otherwise Inventor will apply the load/constrain to the whole surface face.

Did you find this reply helpful ? If so please use the Accept as Solution or Kudos button below.

IV2015 SP1 PDSU / Sim Mech 2015 r1 /
Win7-64
EVGA X79 - Classified, iCore7 3930k 32Gb Quad-Channel
950Gb (2 x 500Gb Sata III SSD RAID0 Adaptec 6805E Controller)
Nvidia GTX-690 Classified - 340.52
SpacePilot Pro 3.17.7, 6.17., 4.11
Delta Tau Chi ΔΤΧ
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.