Inventor General Discussion

Inventor General Discussion

Reply
Distinguished Contributor
scoopthepoop2000
Posts: 128
Registered: ‎02-16-2007
Message 1 of 10 (587 Views)

Stainless steel channel

587 Views, 9 Replies
03-28-2013 05:43 AM

I am using IV 2010. Does anyone have any stainless steel channel drawn up? Particularly 3 X 4.75#,  4 X 6.69# and 6 X 8.3#.  Thanks.

*Expert Elite*
Cadmanto
Posts: 3,356
Registered: ‎12-07-2011
Message 2 of 10 (557 Views)

Re: Stainless steel channel

03-28-2013 11:03 AM in reply to: scoopthepoop2000

Have you tried looking in content center?

channel.PNG

 

check.PNGIf this solved your issue please mark this posting "Accept as Solution".

Or if you like something that was said and it was helpful, Kudoskudos.PNG are appreciated. Thanks!!!! :smileyvery-happy:

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

Distinguished Contributor
scoopthepoop2000
Posts: 128
Registered: ‎02-16-2007
Message 3 of 10 (545 Views)

Re: Stainless steel channel

03-28-2013 11:50 AM in reply to: scoopthepoop2000

All I have in my content center are some ANSI steel and a bunch of other foreign industrial standards none of which appear to be stainless or have the correct profile for a stainless channel.  Thanks.

*Expert Elite*
mrattray
Posts: 2,538
Registered: ‎09-13-2011
Message 4 of 10 (540 Views)

Re: Stainless steel channel

03-28-2013 11:55 AM in reply to: scoopthepoop2000

I may be wrong, but I'm pretty sure stainless channels use the same profile as steel channels.

Mike (not Matt) Rattray

*Expert Elite*
Cadmanto
Posts: 3,356
Registered: ‎12-07-2011
Message 5 of 10 (538 Views)

Re: Stainless steel channel

03-28-2013 11:59 AM in reply to: scoopthepoop2000

Make sure you don't have any filters preventing you frm seeing what you want to see.

 

check.PNGIf this solved your issue please mark this posting "Accept as Solution".

Or if you like something that was said and it was helpful, Kudoskudos.PNG are appreciated. Thanks!!!! :smileyvery-happy:

Best Regards,
Scott McFadden
Inventor Professional 2014
(Colossians 3:23-25)

Distinguished Contributor
scoopthepoop2000
Posts: 128
Registered: ‎02-16-2007
Message 6 of 10 (535 Views)

Re: Stainless steel channel

03-28-2013 12:02 PM in reply to: mrattray

I am not sure they are, the only thing that I have to go by is my old Ryerson stock book and it shows the web, the flange, and the weight being different.

Valued Mentor
RayFeiler
Posts: 402
Registered: ‎10-07-2008
Message 7 of 10 (537 Views)

Re: Stainless steel channel

03-28-2013 12:02 PM in reply to: scoopthepoop2000

The profile should be the same as ANSI MC/C just insert as custom and then change the material.

Chanel.png

Product Design Suite Ultimate 2014 64-Bit

Sometimes you just need a good old reboot.
*Expert Elite*
mrattray
Posts: 2,538
Registered: ‎09-13-2011
Message 8 of 10 (530 Views)

Re: Stainless steel channel

03-28-2013 12:05 PM in reply to: scoopthepoop2000

I don't even have the sizes your looking for in my Alro book (under SS or HRS).

Mike (not Matt) Rattray

Valued Mentor
RayFeiler
Posts: 402
Registered: ‎10-07-2008
Message 9 of 10 (522 Views)

Re: Stainless steel channel

03-28-2013 12:07 PM in reply to: scoopthepoop2000

Also, if the sizes don't match you can change them as well if you insert as custom.

Product Design Suite Ultimate 2014 64-Bit

Sometimes you just need a good old reboot.
*Expert Elite*
mrattray
Posts: 2,538
Registered: ‎09-13-2011
Message 10 of 10 (517 Views)

Re: Stainless steel channel

03-28-2013 12:12 PM in reply to: RayFeiler

I just use i-Features to place structural components. Then I can just populate it with whatever I need it to be.

Mike (not Matt) Rattray

Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Do you have 60 seconds to spare? The Autodesk Community Team is revamping our site ranking system and we want your feedback! Please click here to launch the 5 question survey. As always your input is greatly appreciated.