Inventor General Discussion

Inventor General Discussion

Reply
Contributor
22 Posts
0 Kudos
Registered: ‎10-25-2012
Post 1 of 8
Accepted Solution

Splitting the horizontal spline

324 Views, 7 Replies
10-25-2012 06:09 AM

I have followed every direction in the wikihelp spline and surfaces portion when creating the mouse but, for some reason, every time I try to split the horizontal section I get a message saying "The attempted operation did not successfully complete due to unforeseen problems. Try with different options or inputs." But when I go to split the vertical spline it splits just fine. What can I do to fix this? Thank you.

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

*Expert Elite*
28,642 Posts
2,129 Kudos
Registered: ‎04-20-2006
Post 2 of 8

Re: Splitting the horizontal spline

10-25-2012 06:50 AM in reply to: T.pot

Attach your ipt file here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
22 Posts
0 Kudos
Registered: ‎10-25-2012
Post 3 of 8

Re: Splitting the horizontal spline

10-25-2012 10:49 AM in reply to: JDMather

Mouse Spline file. I am not the only one that this has happened to.

*Expert Elite*
28,642 Posts
2,129 Kudos
Registered: ‎04-20-2006
Post 4 of 8

Re: Splitting the horizontal spline

10-25-2012 11:09 AM in reply to: T.pot

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
22 Posts
0 Kudos
Registered: ‎10-25-2012
Post 5 of 8

Re: Splitting the horizontal spline

10-25-2012 11:26 AM in reply to: JDMather
*Expert Elite*
28,642 Posts
2,129 Kudos
Registered: ‎04-20-2006
Post 6 of 8

Re: Splitting the horizontal spline

10-25-2012 11:40 AM in reply to: T.pot

You put a link to your hard drive.
I was execting an internet url to the on-line wiki.

Well I'll see if I can find the page.

 

http://wikihelp.autodesk.com/Inventor/enu/2013/Help/0126-Tutorial126/0127-Inventor127/0514-Splines_5...

 

http://wikihelp.autodesk.com/User:drafts/505206

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
22 Posts
0 Kudos
Registered: ‎10-25-2012
Post 7 of 8

Re: Splitting the horizontal spline

10-26-2012 07:38 AM in reply to: JDMather

The top URL that you sent me is basically the same thing.

*Expert Elite*
28,642 Posts
2,129 Kudos
Registered: ‎04-20-2006
Post 8 of 8

Re: Splitting the horizontal spline

10-26-2012 10:00 AM in reply to: T.pot

T.pot wrote:

The top URL that you sent me is basically the same thing.


It should be exactly the same thing - I posted the url here for others that might come across this thread in a search since you posted a path to your C drive that we are not likely to have access to.

I then posted a correction to the page, but I guess they didn't like my suggestion.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2015 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are you interested in helping shape the future of the Autodesk Community? To participate in this brief usability study, please click here. Your time and input is greatly appreciated!