Inventor General Discussion

Inventor General Discussion

Reply
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 1 of 8 (290 Views)
Accepted Solution

Splitting the horizontal spline

290 Views, 7 Replies
10-25-2012 06:09 AM

I have followed every direction in the wikihelp spline and surfaces portion when creating the mouse but, for some reason, every time I try to split the horizontal section I get a message saying "The attempted operation did not successfully complete due to unforeseen problems. Try with different options or inputs." But when I go to split the vertical spline it splits just fine. What can I do to fix this? Thank you.

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

*Expert Elite*
JDMather
Posts: 26,889
Registered: ‎04-20-2006
Message 2 of 8 (283 Views)

Re: Splitting the horizontal spline

10-25-2012 06:50 AM in reply to: T.pot

Attach your ipt file here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 3 of 8 (263 Views)

Re: Splitting the horizontal spline

10-25-2012 10:49 AM in reply to: JDMather

Mouse Spline file. I am not the only one that this has happened to.

*Expert Elite*
JDMather
Posts: 26,889
Registered: ‎04-20-2006
Message 4 of 8 (258 Views)

Re: Splitting the horizontal spline

10-25-2012 11:09 AM in reply to: T.pot

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 5 of 8 (248 Views)

Re: Splitting the horizontal spline

10-25-2012 11:26 AM in reply to: JDMather
*Expert Elite*
JDMather
Posts: 26,889
Registered: ‎04-20-2006
Message 6 of 8 (241 Views)

Re: Splitting the horizontal spline

10-25-2012 11:40 AM in reply to: T.pot

You put a link to your hard drive.
I was execting an internet url to the on-line wiki.

Well I'll see if I can find the page.

 

http://wikihelp.autodesk.com/Inventor/enu/2013/Help/0126-Tutorial126/0127-Inventor127/0514-Splines_5...

 

http://wikihelp.autodesk.com/User:drafts/505206

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 7 of 8 (210 Views)

Re: Splitting the horizontal spline

10-26-2012 07:38 AM in reply to: JDMather

The top URL that you sent me is basically the same thing.

*Expert Elite*
JDMather
Posts: 26,889
Registered: ‎04-20-2006
Message 8 of 8 (200 Views)

Re: Splitting the horizontal spline

10-26-2012 10:00 AM in reply to: T.pot

T.pot wrote:

The top URL that you sent me is basically the same thing.


It should be exactly the same thing - I posted the url here for others that might come across this thread in a search since you posted a path to your C drive that we are not likely to have access to.

I then posted a correction to the page, but I guess they didn't like my suggestion.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Announcements
Are you familiar with the Autodesk Expert Elites? The Expert Elite program is made up of customers that help other customers by sharing knowledge and exemplifying an engaging style of collaboration. To learn more, please visit our Expert Elite website.
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.