Inventor General Discussion

Inventor General Discussion

Reply
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 1 of 8 (308 Views)
Accepted Solution

Splitting the horizontal spline

308 Views, 7 Replies
10-25-2012 06:09 AM

I have followed every direction in the wikihelp spline and surfaces portion when creating the mouse but, for some reason, every time I try to split the horizontal section I get a message saying "The attempted operation did not successfully complete due to unforeseen problems. Try with different options or inputs." But when I go to split the vertical spline it splits just fine. What can I do to fix this? Thank you.

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

*Expert Elite*
JDMather
Posts: 27,983
Registered: ‎04-20-2006
Message 2 of 8 (301 Views)

Re: Splitting the horizontal spline

10-25-2012 06:50 AM in reply to: T.pot

Attach your ipt file here.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 3 of 8 (281 Views)

Re: Splitting the horizontal spline

10-25-2012 10:49 AM in reply to: JDMather

Mouse Spline file. I am not the only one that this has happened to.

*Expert Elite*
JDMather
Posts: 27,983
Registered: ‎04-20-2006
Message 4 of 8 (276 Views)

Re: Splitting the horizontal spline

10-25-2012 11:09 AM in reply to: T.pot

Extend the edge of the surface.

It must completely cut the solid.

 

Also, Sketches 4,6 & 8 are not fully constrained.  Add construction line from projected orgin to midpoint of splines.

 

Can you post the url to the wiki page so that I can submit suggested clarifications.

 

Extend Surface.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 5 of 8 (266 Views)

Re: Splitting the horizontal spline

10-25-2012 11:26 AM in reply to: JDMather
*Expert Elite*
JDMather
Posts: 27,983
Registered: ‎04-20-2006
Message 6 of 8 (259 Views)

Re: Splitting the horizontal spline

10-25-2012 11:40 AM in reply to: T.pot

You put a link to your hard drive.
I was execting an internet url to the on-line wiki.

Well I'll see if I can find the page.

 

http://wikihelp.autodesk.com/Inventor/enu/2013/Help/0126-Tutorial126/0127-Inventor127/0514-Splines_5...

 

http://wikihelp.autodesk.com/User:drafts/505206

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Contributor
T.pot
Posts: 22
Registered: ‎10-25-2012
Message 7 of 8 (228 Views)

Re: Splitting the horizontal spline

10-26-2012 07:38 AM in reply to: JDMather

The top URL that you sent me is basically the same thing.

*Expert Elite*
JDMather
Posts: 27,983
Registered: ‎04-20-2006
Message 8 of 8 (218 Views)

Re: Splitting the horizontal spline

10-26-2012 10:00 AM in reply to: T.pot

T.pot wrote:

The top URL that you sent me is basically the same thing.


It should be exactly the same thing - I posted the url here for others that might come across this thread in a search since you posted a path to your C drive that we are not likely to have access to.

I then posted a correction to the page, but I guess they didn't like my suggestion.

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Announcements
Are You Going To Be @ AU 2014? Feel free to drop by our AU topic post and share your plans, plug a class that you're teaching, or simply check out who else from the community might be in attendance. Ohh and don't forgot to stop by the Autodesk Help | Learn | Collaborate booths in the Exhibit Hall and meet our community team if you get a chance!