Inventor General Discussion

Inventor General Discussion

Reply
Contributor
wmd2
Posts: 20
Registered: ‎10-23-2012
Message 1 of 6 (289 Views)

slotting a cap screw

289 Views, 5 Replies
11-16-2012 04:31 PM

Mr Mather,

Experiencing some difficulty slotting the cap screw shown. The problem is this: an additional sketch is created using a rectangle .313 * .094 centered .2815 * .047 from the center of the screwhead. The sketch gets finished the extrusion is created but does not show up. The extrusion is not visible even though a new sketch was created.

Contributor
wmd2
Posts: 20
Registered: ‎10-23-2012
Message 2 of 6 (286 Views)

Re: slotting a cap screw

11-16-2012 04:47 PM in reply to: wmd2

Here is the drawing with the extrusion. However, when the screw is rotated from the isometric view to a front view the extrusion is no longer visible. What needs to be corrected?

Distinguished Contributor
luiww
Posts: 122
Registered: ‎08-09-2010
Message 3 of 6 (270 Views)

Re: slotting a cap screw

11-16-2012 08:38 PM in reply to: wmd2

You need to close the profile as the centreline is not recognised as part of the profile.  Attached is the closed profile for the screw body.

Contributor
wmd2
Posts: 20
Registered: ‎10-23-2012
Message 4 of 6 (235 Views)

Re: slotting a cap screw

11-18-2012 12:05 PM in reply to: luiww

Ok I see what you did. However, the caphead is supposed to be round on the top. So, how is that design feature accomodated with the slotting?

*Pro
sbixler
Posts: 1,922
Registered: ‎09-15-2003
Message 5 of 6 (216 Views)

Re: slotting a cap screw

11-18-2012 02:14 PM in reply to: wmd2

Have you had any training?  Worked through any tutorials?

 

You have produced two disconnected surfaces and then extruded a third one through those two, producing a third surface.  I think that you want a single solid, correct?

 

I don't have 2012 installed at home, so I can't produce a model for you.  But you want to fix your first sketch first- it's not fully constrained (constrain it to the origin point), and the center line is actually two lines which are construction type.  Change it to one normal (non-construction) centerline type line.  With a centerline-type line, dimensions to other features are taken as diameters rather than radii.

 

Now your second sketch needs to be incorporated into the first one-- I don't see any benefit to making it a separate feature.  When you revolve that sketch you should get a solid model rather than a surface model.

 

Now for the slot-- again, the profile needs to be closed, and it should cut the slot exactly as you wish.

 

JD Mather has a very good basic skills white paper available.  I don't have the link saved at home, but a quick browse through his responses to various problems should turn up the link.

*Expert Elite*
JDMather
Posts: 27,424
Registered: ‎04-20-2006
Message 6 of 6 (209 Views)

Re: slotting a cap screw

11-18-2012 03:42 PM in reply to: wmd2

Start a new part file.

Create the sketch shown below.  One sketch!

Attach the file here.

 

You might also read this documnent.

http://home.pct.edu/~jmather/SkillsUSA%20University.pdf

 

Sketch1.PNG

Please mark this response as "Accept as Solution" if it answers your question.
-----------------------------------------------------------------------------------------
Autodesk Inventor 2014 Certified Professional
Autodesk AutoCAD 2013 Certified Professional
Certified SolidWorks Professional
Inventor Professional 2015-SP1 64-bit
http://www.autodesk.com/edcommunity
http://home.pct.edu/~jmather/content/DSG322/inventor_surface_tutorials.htm
Post to the Community

Have questions about Autodesk products? Ask the community.

New Post
Need installation help?

Start with some of our most frequented solutions or visit the Installation and Licensing Forum to get help installing your software.